2E-6 THOMAS & BETTS, 2E-6 Datasheet - Page 56

• Manufacturer Part Number: 2E-6
• Description: TERMINAL, BUTT SPLICE, CRIMP
• Manufacturer: THOMAS & BETTS
• Type: Buttr

Specifications of 2E-6

• Connector Type: Butt Splice
• Termination Method: Crimp
• Wire Size (awg): 6-5
• Contact Plating: Tin
• Insulator Material: Non-Insulated
• Angle: Straight
• Brand/series: Sta-Kon®
• Insulation Type: Non-Insulated
• Length, Overall: 1.12 "
• Package Quantity: 20
• Primary Type: Splice
• Standards: UL Listed, CSA Certified
• Width, Overall: 0.37 "
• Wire Size: 6-5 AWG
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

F-56
Platings/Finish
Electroplated-Tin is standard finish. All others require minimum order
quantities and are generally not stocked. Alternative platings are as
follows: Gold, Silver, Tin-Alloys, Nickel or plain finish. See table (below)
for specification information:
FINISH
Gold Plate
Nickel Plate
Plain Finish
Silver Plate
The proper installation procedure for the quality assured connection!
The proper installation of terminals, splices, and connectors is very important
to the efficient performance of an electrical system. The properly installed
connector will enable good conductivity through the termination. A poor
termination results in a high-resist ance connection. A poor connector
installation may cause damage or failure of an entire system. Certain
basic requirements must be met to make a good termination.
Before the connector or terminal is installed on the conductor,
follow these recommended practices:
•
•
Strip the insulation carefully to avoid nicking
or cutting conductor strands
Strip the insulation to the proper length so the conductors can
be inserted fully into the connector barrel; the wire/cable should
be visible in the inspection hole of the lug; the proper strip length
can be found on page F-45.
www.tnb.com
Technical Info
SUFFIX
NP
GP
PF
SP
MIL-G-45204 Type II, Grade B, C, D, Class O
MIL-T-16366 Type I or II, 400° F, 204° C
QQ-N-290 Class 2, Grade G
SPEC.
None
United States
Tel: [phone]
Fax: [phone]
800.816.7809
TEMP. RATING
260˚ C
260˚ C
150˚ C
150˚ C
ERG2001
Technical Services
Tel: [phone]
Listing
Sta-Kon
and listed to UL
disconnects to UL 310, and all appli cable products
to CSA 22.2.
Sta-Kon
TERMINALS & SPLICES
INSULATION RATING
Nylon
Vinyl
Tefzel
Disconnects
Non-Insulated
**1000V fixture or sign
Installation Procedure
1. Train the wires to eliminate
2. Open handles fully.
3. Insert terminal in proper die nest
4. Close handles slightly to secure
5. Insert properly stripped
6. Complete crimp
fanning of strands.
and locate it as shown above.
When crimping a butt splice,
position in proper die nest
with window facing indentor.
terminal. Do not deform terminal.
wire into terminal.
by closing handles.
®
®
Rings, Forks and Locking Forks are tested
®
®
486A, two-way splices to UL 486C,
Technical Data
FLAMMABILITY
UL
V-2
V-0
V-0
—
®
94
stripped wire
rest
Shure-Stake
tools are matched
to terminals.
VOLTAGE
600V**
600V**
600V**
300V
600V
stripping
TEMPERATURE
length
orient tongue
®
terminal
as shown
105° C
105° C
150° C
105° C
150º C
indentor