2222 370 11474 Vishay, 2222 370 11474 Datasheet - Page 13
![CAPACITOR, 0.47UF 63V CAPACITOR, 0.47UF 63V](/photos/25/81/258100/42245879_sml.jpg)
2222 370 11474
Manufacturer Part Number
2222 370 11474
Description
CAPACITOR, 0.47UF 63V CAPACITOR, 0.47UF 63V
Manufacturer
Vishay
Series
2222370r
Datasheet
1.2222_370_11105.pdf
(18 pages)
Specifications of 2222 370 11474
Capacitance
0.47UF
Voltage Rating, Ac
40V
Voltage Rating, Dc
63V
Capacitor Dielectric Type
POLYESTER
Tolerance,
10%
Tolerance, -
10%
Temp, Op. Max
100(DEGREE C)
Rohs Compliant
YES
HEAT CONDUCTIVITY (G) AS A FUNCTION OF (ORIGINAL) PITCH AND CAPACITOR BODY THICKNESS IN mW/°C
POWER DISSIPATION AND MAXIMUM COMPONENT TEMPERATURE RISE
The power dissipation must be limited in order not to exceed the maximum allowed component temperature rise as a function of
the free ambient temperature.
The power dissipation can be calculated according type detail specification “HQN-384-01/101: Technical Information Film
Capacitors”.
The component temperature rise (ΔT) can be measured (see section “Measuring the component temperature” for more details)
or calculated by ΔT = P/G:
MEASURING THE COMPONENT TEMPERATURE
A thermocouple must be attached to the capacitor body as in:
The temperature is measured in unloaded (T
The temperature rise is given by ΔT = T
To avoid radiation or convection, the capacitor should be tested in a wind-free box.
APPLICATION NOTE AND LIMITING CONDITIONS
These capacitors are not suitable for mains applications as across-the-line capacitors without additional protection, as described
hereunder. These mains applications are strictly regulated in safety standards and therefore electromagnetic interference
suppression capacitors conforming the standards must be used.
To select the capacitor for a certain application, the following conditions must be checked:
1. The peak voltage (U
2. The peak-to-peak voltage (U
3. The voltage peak slope (dU/dt) shall not exceed the rated voltage pulse slope in an RC-circuit at rated voltage and without
4. The maximum component surface temperature rise must be lower than the limits (see figure max. allowed component
5. Since in circuits used at voltages over 280 V peak-to-peak the risk for an intrinsically active flammability after a capacitor
6. When using these capacitors as across-the-line capacitor in the input filter for mains applications or as series connected with
Document Number: 28108
Revision: 08-Dec-08
ringing. If the pulse voltage is lower than the rated DC voltage, the rated voltage pulse slope may be multiplied by U
divided by the applied voltage.
For all other pulses following equation must be fulfilled:
T is the pulse duration
temperature rise).
breakdown (short circuit) increases, it is recommended that the power to the component is limited to 100 times the values
mentioned in the table: “Heat conductivity”
an impedance to the mains the applicant must guarantee that the following conditions are fulfilled in any case (spikes and
surge voltages from the mains included).
• ΔT = Component temperature rise (°C)
• P = Power dissipation of the component (mW)
• G = Heat conductivity of the component (mW/°C)
P
) shall not be greater than the rated DC voltage (U
.
W
(mm)
2.5
3.5
4.5
6.0
max.
P-P
) shall not be greater than 2
C
- T
For technical questions, contact: dc-film@vishay.com
amb
amb
MKT Radial Potted Type
.
) and maximum loaded condition (T
DC Film Capacitor
2 x
√
T
∫
0
2 x U
⎛
⎝
dU
------ -
dt
Thermocouple
⎞
⎠
2
Rac
x dt
to avoid the ionisation inception level
<
Rdc
U
Rdc
)
HEAT CONDUCTIVITY (mW/°C)
x
⎛
⎝
C
dU
------ -
dt
).
⎞
⎠
rated
PITCH 5 mm
Vishay BCcomponents
2.5
3.0
4.0
5.5
MKT 370
www.vishay.com
Rdc
and
89