B45196E3105K109 Kemet, B45196E3105K109 Datasheet - Page 4
![CAPACITOR, 1.0UF 16V RL 2000CAPACITOR, 1.0UF 16V RL 2000](/photos/25/87/258765/42245823_sml.jpg)
B45196E3105K109
Manufacturer Part Number
B45196E3105K109
Description
CAPACITOR, 1.0UF 16V RL 2000CAPACITOR, 1.0UF 16V RL 2000
Manufacturer
Kemet
Series
B45196Er
Datasheet
1.B45196E3105K109.pdf
(6 pages)
Specifications of B45196E3105K109
Capacitance
1UF
Voltage Rating, Dc
16V
Capacitor Dielectric Type
TANTALUM ELECTROLYTIC
Tolerance,
10%
Tolerance, -
10%
Temp, Op. Min
-55(DEGREE C)
Rohs Compliant
YES
Voltage Rating
16 Volts
Tolerance
10 %
Operating Temperature Range
- 55 C to + 125 C
Package / Case
1206 (3216-18 metric)
Product
Tantalum Solid High Temperature
Dissipation Factor Df
4
Leakage Current
0.5 uAmp
Termination Style
SMD/SMT
Lead Free Status / Rohs Status
Details
Cautions and warnings
When using tantalum capacitors with a manganese dioxide coating, the following cautions and
warnings should be taken into account:
Polarity
Because tantalum capacitors are polar capacitors, it is important to observe their polarity
markings (positive pole on the anode, negative pole on the cathode). Any incorrect polarity
resulting from the sum of the AC and DC voltage components must be smaller than or equal to
the permitted polarity reversal voltage (see “General technical information”, section 4.6 and
section 4.8 under www.epcos.com/tantalum_capacitors). To avoid reducing their reliability, this
voltage may only occur for a short time, at most five times for a duration of one minute per hour.
Voltage
The maximum continuous voltage depends on the ambient temperature. Within the temperature
range of -55 to +85 C, the rated voltage is equal to the maximum continuous voltage. Between +
85 and + 125 C the maximum continuous voltage must be reduced linearly from the full rated
voltage to 2/3 of it (derating). At 150 C (only B4519*P series) the voltage must be reduced to 1/2
and at 175 C (only B4519*T series) to 1/3 of the rated voltage. Operation below the maximum
continuous voltage has a positive effect on the capacitor’s failure rate. The maximum continuous
voltage must not be exceeded (see“Quality and environment”, section 1.11 under
www.epcos.com/tantalum_capacitors).
All unfavourable operating conditions (such as possible line overvoltages, unfavourable
tolerances of the transformation ratio of the line transformer in the equipment, repeated
overvoltages when the equipment is switched on, high ambient temperatures) must be taken into
account when determining the operating voltage.
The surge voltage is the maximum voltage (peak value) that may be applied to the capacitor for
short periods, at most five times for a total duration of up to 1 minute per hour. The surge voltage
must not be applied for periodic charging and discharging in the course of normal operation and
cannot be part of the operating voltage. The permissible surge voltage for all capacitors in this
data book is 1.3 x the rated voltage. The occurrence of voltage impulses (transient voltages) that
exceed the surge voltage may lead to irreparable damage.
Capacitance
The actual capacitance of a capacitor can deviate from the rated capacitance by as much as the
full magnitude of the tolerance at delivery. The capacitance varies with the temperature (at +125
information”, section 5 under www.epcos.com/tantalum_capacitors).
Please read Cautions and warnings and
Important notes at the end of this document.
Tantalum chip capacitors
Standard / HighCap
C +12% up to +20%) and decreases with increasing frequency (see “General technical
Page 4 of 6
B45196E3105+10*