ERJM1WSF10MU Panasonic, ERJM1WSF10MU Datasheet
![RESISTOR, 2512, 0R01, 1%, 2W](/photos/26/15/261517/1577576-40_sml.jpg)
ERJM1WSF10MU
Specifications of ERJM1WSF10MU
Available stocks
Related parts for ERJM1WSF10MU
ERJM1WSF10MU Summary of contents
Page 1
... ERJM1WS [.252+/-.010] 2.Power Derating Curve Category Temperature Range (Operating Temperature Range): -55 to +170 deg.C 120 100 -55 -40 PANASONIC ELECTRONIC DEVICES CO.,LTD. ERJM1WS type Terminal Alloy Metal Metal W T 3.20+/-0.25 0.80+/-0.30 [.126+/-.010] [.031+/-.012] ...
Page 2
... The surface of terminal is covered by the plating. And the plating is Construction hard to fade, then don't have unevenness, flaw, pinhole and discoloration. 3. The terminal is connected with resistive plate certainly. PANASONIC ELECTRONIC DEVICES CO.,LTD. Specifications When you use one at ambient temperature over 1.0W 70deg.C, the load power shall be reduced as (70deg ...
Page 3
... Coefficient 5m 5m 10m Intermittent R = +/-(5%+0.5m ) Overload No evidence of flash over, mechanical Dielectric damage, arcing or insulation Withstanding breakdown. Insulation Resistance PANASONIC ELECTRONIC DEVICES CO.,LTD 1. Top terminal Test Methods(Based on JIS - C5201) Measuring current: 1A 20deg.C 65%RH -6 350+/-100 10 /deg.C -6 100+/-50 10 /deg.C Sequence of temperature: ...
Page 4
... Terminal Strength Without distinct deformation Bending Strength in appearance Solderability min. 95% coverage Resistance +/-(5%+0.5m ) Soldering Heat PANASONIC ELECTRONIC DEVICES CO.,LTD. Test Methods(Based on JIS-C5201) Copper plate 0.4mm Pull speed Fixed min. 4.9N Substrate : Glass Epoxy (t=1.6mm) Span : 90mm Bending Distance : 2mm (10 seconds) ERJM1WT ...
Page 5
... ERJM1WS type 11.Recommended Pad Layout ERJM1WT type 3.1mm 3.4mm 2.2mm 12.Manufacturing Country Indonesia or Japan PANASONIC ELECTRONIC DEVICES CO.,LTD. Test Methods(Based on JIS-C5201) Resistors shall be exposed at 125+/-3deg.C for 1000+48/-0 hours. -55+/-3deg.C 30minutes Normal temp. 30minutes +125+/-3deg.C 30minutes Resistors shall be exposed at 60+/-2deg.C and 90 to 95% relative humidity in a humidity test chamber for 1000+48/-0 hours ...
Page 6
... PANASONIC ELECTRONIC DEVICES CO.,LTD. Spec. No. 151-RJM-E01MM ...
Page 7
... Chemical substances. 4 All the materials used in this part contain no brominated materials of PBBOs or PBBs as the flame-retardant you need the notice by letter of "A preliminary judgement on the Laws of Japan foreign exchange and Foreign Trade control", be sure to let us know. PANASONIC ELECTRONIC DEVICES CO.,LTD. Spec. No. 151-RJM-E01MM ...
Page 8
... Soldering profile is measured at the mounting position of the resistor. Reflow soldering shall be within two times. The regulation is for the resistor and applies to 10-4 Resistance to Soldering Heat 2 The problems caused by solder and flux are not our responsibility. PANASONIC ELECTRONIC DEVICES CO.,LTD. Spec. No. 151-RJM-E01MM ...
Page 9
... Adhesive Tape 2-2 Carrier Tape Dimensions 3.60+/-0.20 6.90+/-0.20 [.141+/-.008] [.272+/-.008 4.00+/-0.05 8.00+/-0.10 [.157+/-.002] [.314+/-.004] PANASONIC ELECTRONIC DEVICES CO.,LTD. 15.4+/-1.0 min. Sprocket Hole B Compartment Chip Resistor 12.0+/-0.30 5.50+/-0.05 [.472+/-.012] [.217+/-.002 ...
Page 10
... Side of Reel(Marking shall be on one side.) 1) Part Name('Fixed metal plate flat chip resistor' following part name on invoice) 2) Part Number 3) Quantity 6) Manufacturing Country Packaging Box 1) Part Number 2) Quantity 3) Maker Name PANASONIC ELECTRONIC DEVICES CO.,LTD. Peeling Direction 10 Top Tape Tape Marking 4) Lot Number 5) Maker Name Spec. No. ...