8G16D 2K 0.1 RHOPOINT, 8G16D 2K 0.1 Datasheet
![RESISTOR, 0.33W 0.1% 2K](/photos/26/14/261466/42253987_sml.jpg)
8G16D 2K 0.1
Manufacturer Part Number
8G16D 2K 0.1
Description
RESISTOR, 0.33W 0.1% 2K
Manufacturer
RHOPOINT
Series
8G16Dr
Datasheet
1.8G16D_250R_0.1.pdf
(2 pages)
Specifications of 8G16D 2K 0.1
Resistance
2kohm
Resistance Tolerance
± 0.1%
Power Rating
330mW
Voltage Rating
175V
Resistor Element Material
Wirewound
No. Of Pins
2
Body
RoHS Compliant
Temperature Coefficient
± 5ppm/°C
Resistor Case Style
Axial
Rohs Compliant
Yes
2
P R E C I S I O N
ECONISTOR
FEATURES
OHMIC VALUES
Econistors are available in 111 standard values from 1 to 1M
and in any “non-standard” values from 1
tolerances are available; 0.1%, 0.01% and 0.005% (0.005%
available on values of 100
includes all values below 700K ; values of 700K and above
are type 8E24. The types are identical except dimensionally;
Type 8E16 is 12.7mm long, Type 8E24 is 19.05mm long. Both
are manufactured using all welded construction.
* Stocked in ±0.1% tolerance only. † Stocked in ±0.01% tolerance only.
A number of values listed are RTD simulation values. See page 6 for temperature equivalents.
±3ppm per degree Centigrade temperature co-efficient
Full load stability ±50ppm maximum after three years
Tolerance ±0.005%, ±0.01% and ±0.1%
Axial leads
From stock in 111 popular standard values; to order in
any value from 1 ohm to 1.1 Meg
10
1
2
†
†
†
103.90
107.79
Stocked in ±0.1% and ±0.01% in listed values shown below
and above only). Type 8E16
†
†
†
†
†
†
†
†
†
†
†
†
†
(8E16 & 8E24)
194.07
200.00
212.02
to 1.1M . Three
W I R E W O U N D
†
†
†
†
680
700
800
SPECIFICATIONS
Tolerance at 25°C:
Temperature Co-efficient:
Full Load Stability:
No Load Stability:
Power Rating:
Maximum Continuous Working Voltage:
Noise:
Encapsulation:
Windings:
Holland Road, Hurst Green, Oxted, Surrey, RH8 9AX, England
±0.005%, ±0.01%, ±0.1%
±3ppm/°C typical over 0°C to +85°C
±5ppm maximum over –55°C to +125°C
±35ppm/10,000hours
±25ppm/10,000 hours
±35ppm/26,000 hours
0.33 watt (+85°C)
Up to 250V DC or peak as determined by
Essentially non-measurable
Moulded epoxy
Balanced multiple for low reactance. Exclusive ‘air cushion’ technique
provides virtually stressless elements for improved performance. Non-
inductively wound. Direction of winding reversed at half turns point.
Outside UK Tel: +44 1883 717 988 — Fax: +44 1883 712 938
Tel: Oxted 01883717988 — Fax: Oxted 01883 712938
4.7K *
5.0K
5.6K *
}
Thermal EMF:
Leads:
over full temperature range;
–55°C to +125°C
<0.4 V/°C typical <1.5 V/°C maximum
±50ppm/26,000 hours
0.25 watt (+110°C)
22 AWG tinned copper
R E S I S T O R S
27K *
30K
33K *
PR
available to order
Any non-listed
1 to 1.1M
value from
180K
200K
250K
Related parts for 8G16D 2K 0.1
8G16D 2K 0.1 Summary of contents
Page 1
ECONISTOR FEATURES ±3ppm per degree Centigrade temperature co-efficient Full load stability ±50ppm maximum after three years Tolerance ±0.005%, ±0.01% and ±0.1% Axial leads From stock in 111 popular standard values; to ...
Page 2
... The thermal EMF of the resistance material to copper join for Econistors is typically <0.4 V/° Style and general specifications Matched pairs and ratio matched resistors are available against specific enquiries (8E16 & 8E24) ~ CONSTRUCTION Econistors are wound on a proprietary multi-section bobbin with the termination wires moulded deep into the body of the bobbin ...