HHV-50JT-52-4M7 Yageo, HHV-50JT-52-4M7 Datasheet - Page 6
![no-image](/images/manufacturer_photos/0/7/724/yageo_sml.jpg)
HHV-50JT-52-4M7
Manufacturer Part Number
HHV-50JT-52-4M7
Description
RESISTOR, 0.5W, 5%, 4M7
Manufacturer
Yageo
Series
HHVr
Datasheet
1.HHV-25JT-52-100K.pdf
(8 pages)
Specifications of HHV-50JT-52-4M7
Resistance
4.7Mohm
Resistance Tolerance
± 5%
Power Rating
500mW
Voltage Rating
3.5kV
Resistor Element Material
Metal Film
No. Of Pins
2
Svhc
No SVHC
Temperature Coefficient
± 200ppm/°C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
(5) Solderability
(6) Resistance to Solvent
(7) Terminal Strength
(8) Pulse Overload
(9) Load Life in Humidity
(10) Load Life Test
(11) Temperature Cycling Test
(12) Resistance to Soldering Heat
Immerse the specimen into the solder pot at 230 ± 5 °C for 5 ± 0.5 seconds.
At least 95% solder coverage on the termination.
The specimen into the appropriate solvent of IPA condition of ultrasonic machine for 1 minutes.
The specimen is no deterioration of coatings and color code.
Direct Load – Resistors shall be held by one terminal and the load shall be gradually applied in the
direction of the longitudinal axis of the resistor unit the applied load reached 5 pounds。
The load shall be held for 10 seconds. The load of weight shall be ≧ 2.5 kg ( 24.5N ).
Apply 4 times of rated voltage to the specimen at the 1 second on and 25 seconds off cycle, subjected
to voltage application cycles specified in 10,000 time。
The change of the resistance value shall be within ± 1.0% + 0.05 Ω
Place the specimen in a test chamber at 40 °C and 93 % relative humidity. Apply the rated voltage to
the specimen at the 1.5 hours on and 0.5 hour off cycle. The total length of test is 1,000 hours
The change of the resistance value shall be within ± 5.0 % + 0.05 Ω
Placed in the constant temperature chamber of 70 ± 3 °C the resistor shall be connected to the lead wire
at the point of 25mm. Length with each terminal, the resistors shall be arranged not much effected
mutually by the temperature of the resistors and the excessive ventilation shall not be performed, for 90
minutes on and 30 minutes off under this condition the rated D.C. voltage is applied continuously for
1000+48/-0 hours then left at no-load for 1hour, measured at this time the resistance value。
The change of the resistance value shall be within ± 5.0 % + 0.05 Ω.
There shall be no remarkable change in the appearance and the color code shall be legible after the test.
The temperature cycle shown in the following table shall be repeated 5 times consecutively. The
measurement of the resistance value is done before the first cycle and after ending the fifth cycle,
leaving in the room temperature for about 1 hour。
Temperature Cycling Conditions:
The change of the resistance value shall be within ± 1.0 % + 0.05 Ω
After the test the resistor shall be free from the electrical or mechanical damage.
The terminal lead shall be dipped into the solder pot at 260 °C for 10 seconds.
The change of the resistance value shall be within ± 1.0 % + 0.05 Ω
Step
1
2
3
4
Temperature(°C)
155 ± 3
-55 ± 3
25 ± 3
25 ± 3
Page-6
Time (minute)
2 ~3
2 ~3
30
30