PNP10VJT-91-220R Yageo, PNP10VJT-91-220R Datasheet - Page 6
![no-image](/images/manufacturer_photos/0/7/724/yageo_sml.jpg)
PNP10VJT-91-220R
Manufacturer Part Number
PNP10VJT-91-220R
Description
RESISTOR, 10W, 5%, 220R
Manufacturer
Yageo
Series
PNP Vr
Datasheet
1.PNP10VJT-91-100R.pdf
(8 pages)
Specifications of PNP10VJT-91-220R
Resistance
220ohm
Resistance Tolerance
± 5%
Power Rating
10W
Resistor Element Material
Wirewound
No. Of Pins
2
Svhc
No SVHC (15-Dec-2010)
Body
RoHS Compliant
Temperature Coefficient
0, +600ppm/°C
!
!
(4) Insulation Resistance
(5) Solderability
(6) Resistance to Solvent
(7) Terminal Strength
(8) Load Life in Humidity
(10) Temperature Cycling Test
(11) Resistance to Soldering Heat
(9) Load Life Test
Immerse the specimen into the solder pot at 260 ± 5 ° C for 5 ± 0.5 seconds.
At least 95% solder coverage on the termination.
Apply test terminal on lead and resistor body.
The test resistance should be high than 100M ohm.
The specimen into the appropriate solvent of IPA condition of ultrasonic machine for 1 minutes.
The specimen is no deterioration of coatings and color code.
Direct Load – Resistors shall be held by one terminal and the load shall be gradually applied in the
direction of the longitudinal axis of the resistor unit the applied load reacheds 5 pounds
The load shall be held for 10 seconds. The load of weight shall be
Place the specimen in a test chamber at 40 ± 2 ° C and 90 ~ 95 % relative humidity. Apply the rated
voltage to the specimen at the 1.5 hours on and 0.5 hour off cycle. The total length of test is 1,000
hours
The change of the resistance value shall be within ± 5 % + 0.05
Placed in the constant temperature chamber of 70 ± 3 ° C the resistor shall be connected to the lead
wire at the point of 25mm. Length with each terminal, the resistors shall be arranged not much
effected mutually by the temperature of the resistors and the excessive ventilation shall not be
performed, for 90 minutes on and 30 minutes off under this condition the rated D.C. voltage is applied
continuously for 1000+48/-0 hours then left at no-load for 1hour, measured at this time the resistance
value
The change of the resistance value shall be within ± 5 % + 0.05
There shall be no remarkable change in the appearance and the color code shall be legible after the
test.
The temperature cycle shown in the following table shall be repeated 5 times consecutively. The
measurement of the resistance value is done before the first cycle and after ending the fifth cycle,
leaving in the room temperature for about 1 hour
Temperature Cycling Conditions:
The change of the resistance value shall be within ± 1.0 % + 0.05
After the test the resistor shall be free from the electrical or mechanical damage.
The terminal lead shall be dipped into the solder pot at 350 ± 10 ° C for 3 ± 0.5 seconds up to 2 ~ 2.5
mm.
The change of the resistance value shall be within ± 1.0 % + 0.05
Step
1
2
3
4
Temperature(° C)
155 ± 3
-55 ± 3
25 ± 3
25 ± 3
Page-6
Time (minute)
2 ~ 3
2 ~ 3
30
30
.
2.5 kg ( 24.5N ).