RCH50S22001JS06 Vishay, RCH50S22001JS06 Datasheet - Page 3

• Manufacturer Part Number: RCH50S22001JS06
• Description: RESISTOR, 50W 22K
• Manufacturer: Vishay
• Series: RCHr

Specifications of RCH50S22001JS06

• Resistance: 22kohm
• Resistance Tolerance: ± 5%
• Power Rating: 5.5W
• Voltage Rating: 1.285kV
• Resistor Element Material: Thick Film
• Resistor Case Style: Heat Sinkable
• Temperature Coefficient: ± 150ppm/°C
• Tolerance: 5 %
• Operating Temperature Range: - 55 C to + 125 C
• Dimensions: 15.5 mm W x 47.8 mm L x 6 mm H
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

RCH
Vishay Sfernice
RECOMMENDATIONS FOR MOUNTING ONTO A HEATSINK
Surfaces in contact must be carefully cleaned.
The heatsink must have an acceptable flatness: from 0.05 mm to 0.1 mm/100 mm.
Roughness of the heatsink must be around 6.3 µm. In order to improve thermal conductivity, surfaces in contact (alumina,
heat-sink) are coated with a silicone grease (type Sl 340 from Rhône-Poulenc or Dow 340 from Dow Corning).
The fastening of the resistor to the heatsink is under pressure control of two screws (not supplied).
In order to improve the dissipation, either forced-air cooling or liquid cooling may be used.
A low thermal radiation of the case allows several resistors to be mounted onto the same heatsink.
Do not forget to respect an insulation value between two resistors (dielectric strength in dry air 1 kV/mm).
In any case the hot spot temperature, measured locally on the case must not exceed 125 °C.
Tests should be performed by the user.
CHOICE OF THE HEATSINK
The user must choose the heatsink according to working conditions of the component (power, room temperature). Maximum
working temperature must not exceed 125 °C. The dissipated power is simply calculated by the following ratio:
Example:
R
www.vishay.com
3
Tightening Torque
on heatsink
TH
: (c-a) for RCH 25 power rating 20 W at ambient temperature + 50 °C.
P:
T:
R
R
TH
TH
:
:
ΔT ≤ 125 °C - 50 °C ≤ 75 °C
R
R
R
Expressed in W
Difference between maximum working temperature and room temperature.
(j-c): Thermal resistance value measured between resistance layer and outer side of the resistor.
It is the thermal resistance of the component (See Special Features table).
(c-a): Thermal resistance value measured between outer side of the resistor and room temperature.
It is the thermal resistance of the heatsink depending on the heatsink itself (type, shape) and the quality of the
fastening device.
TH
TH
TH
(j-c) + R
(j-c) = 1.4 °C/W (Special Features)
(c-a) ≤ 3.75 °C/W - 1.4 °C/W ≤ 2.35 °C/W
TH
(c-a) =
Power Resistors, for Mounting onto a Heatsink
ΔT
-------
0.5 Nm
RCH 5
P
=
For technical questions, contact: [e-mail]
75
----- -
20
= 3.75 °C/W
P
Thick Film Technology
=
----------------------------------------------------------------- -
[
R
TH
(
j c
–
RCH 10
0.6 Nm
)
ΔT
+
R
TH
(
c a
–
)
]
1 ( )
RCH 25
0.7 Nm
Document Number: 50006
Revision: 09-Jun-08
RCH 50
1 Nm