CC0201JRNPO8BN470 Yageo, CC0201JRNPO8BN470 Datasheet - Page 11

• Manufacturer Part Number: CC0201JRNPO8BN470
• Description: CAPACITOR, 0201, 47PF, 25V, NP0, 5%
• Manufacturer: Yageo

Specifications of CC0201JRNPO8BN470

• Capacitor Application: Standard
• Dielectric Characteristic: C0G / NP0
• Capacitance: 47pF
• Capacitance Tolerance: ± 5%
• Voltage Rating: 25V
• Capacitor Case Style: 0201
• No. Of Pins: 2
• Capacitor: RoHS Compliant
• Capacitor Mounting: SMD
• Rohs Compliant: Yes

Apr 19, 2006 V.2
TEST
Bond strength
soldering heat
Resistance to
Rapid change
temperature
Table 6
of plating on
with U
Solderability
Damp heat,
end face
r
load
Test condition, procedure and requirements (continued)
of
Surface-Mount Ceramic Multilayer Capacitors
TEST METHOD
IEC 60384-
21/22
4.8
4.9
4.10
4.11
4.13
PROCEDURE
Precondition: 150 +0/–10 °C for 1 hour, then keep for
24 ±1 hours at room temperature
Preheating: for size ≤ 1206: 120 to 150 °C for 1 minute
Preheating: for size >1206: 100 to 120 °C for 1 minute
and 170 to 200 °C for 1 minute
Solder bath temperature: 260 ±5 °C
Dipping time: 10 ±0.5 seconds
Recovery time: 24 ±2 hours.
Unmounted chips completely immersed in a solder bath
at 235 ±5 °C
Dipping time: 2 ±0.5 seconds
Depth of immersion: 10 mm
Preconditioning;
150 +0/–10 °C for 1 hour, then keep for 24 ±1 hours at
room temperature
5 cycles with following detail:
30 minutes at lower category temperature;
30 minutes at upper category temperature
Recovery time 24 ±2 hours.
Initial measurements; after 150 +0/-10 °C for 1 hour,
then keep for 24 ±1 hours at room temperature
Duration and conditions: 500 ±12 hours at 40 ±2 °C;
90 to 95% RH; U
Final measurement: perform a heat treatment at
150 +0/–10 °C for 1 hour, final measurements shall be
carried out 24 ±1 hours after recovery at room
temperature without load.
Mounting in accordance with IEC 60384-22 paragraph
4.3
Conditions: bending 1 mm at a rate of 1 mm/s, radius jig
340 mm
r
applied
Ultra small
NP0/X5R/X7R/Y5V
REQUIREMENTS
No visible damage
NP0: lΔC/Cl: ≤ 1% or 0.5 pF
whichever is greater
X5R/X7R/Y5V: lΔC/Cl: ≤ 10%
The termination shall be well tinned
NP0: lΔC/Cl: ≤ 0.5% or 0.5 pF
whichever is greater
X5R/X7R: lΔC/Cl: ≤ 10%
Y5V: lΔC/Cl: ≤ 20%
D.F.: within initial specified value
R
The termination shall be well
tinned.
No visual damage
NP0: lΔC/Cl: ≤ 1% or 1 pF
whichever is greater
X5R/X7R: lΔC/Cl: ≤ 15%
Y5V: lΔC/Cl: ≤ 20%
D.F.: within initial specified value
R
NP0: lΔC/Cl: ≤ 2% or 1 pF
whichever is greater
X5R/X7R: lΔC/Cl: ≤ 20%
Y5V: lΔC/Cl: ≤ 30%
NP0/X5R/X7R/Y5V: D.F.: 2 × initial
value max.
NP0: R
≥ 25 seconds, whichever is less
X5R/X7R/Y5V: R
R
is less
ins
ins
ins
: within initial specified value
: within initial specified value
× C
ins
r
6.3 V to 50 V
≥ 2,500 MΩ or R
≥ 25 seconds, whichever
Product specification
ins
≥ 500 MΩ or
www.yageo.com
ins
× C
11
13
r