AME9003AETH AME, AME9003AETH Datasheet - Page 16

• Manufacturer Part Number: AME9003AETH
• Description: CCFL Inverters & Accessories Backlight Controller
• Manufacturer: AME

Specifications of AME9003AETH

• Function: Backlight Controller
• Input Voltage: 3.5 V
• Output Voltage: 5.35 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

AME9003
Driving the CCFL
secondary winding of the AME9003 method is not de-
signed to look like a voltage source to the CCFL lamp.
The circuit acts more like a current source (or a power
source). The voltage at the transformer secondary is pri-
marily determined by the operating point of the CCFL.
The circuit will increase the duty cycle of Q2 thereby
dumping more and more energy across to the secondary
tank circuit until the CCFL tube current achieves regula-
tion or one of the various fault conditions is met.
The start up mode consists of the time from intial power
up until the tube strikes or 1 second elapses. The steady
state mode consists of operation that occurs after the
start up mode finishes.
tubes into striking. It is believed that as a tube ages it
becomes more and more difficult to strike an arc through
the gas. Cold temperatures make this problem even
worse. The AME9003 will allow higher than normal oper-
ating voltages across the CCFL for a period of up to one
second in order to facilitate strking. This feature should
extend the usable life of the CCFL as well as simplifying
start up for ” problem” applications.
Start Up Mode
sitions from a low to a high state a special mode of op-
eration, known as the ” start up mode” , is initiated that
will last for a maximum of one second. The exact dura-
tion of the start up period is determined by capacitor C3
and C31 on the SSC pin. Figure 10 shows a flow chart of
the CCFL ignition sequence described here. The start
up mode will end when one of two conditions is met:
sition on CE) the SSC1ST pin is internally shorted to
VSS so C3 and C31 are in parallel. C3 and C31 are
initially discharged and the voltage on SSC is zero. C31
and C3 are charged up by a 1.5uA current source. When
the voltage at SSC reaches 3 volts the start up mode has
ended. A value of 0.47uF for C31 nominally yields a one
second start up period. C3 is usually a factor of 10 smaller
than C31. If the one second time period ends before the
16
Unlike modified Royer schemes for driving CCFLs the
There are two major modes of operation of the AME9003.
The start up mode is useful for coaxing old or cold
When the circuit is first powered up or the CE pin tran-
On the first cycle after power on (or a low to high tran-
a) The CCFL strikes and the current sense voltage at
the CSDET pin rises above 1.25V.
b) The one second time period ends without the tube
being struck, in this case the circuit will shut down.
AME, Inc.
CCFL strikes then the circuit is shutdown until the user
toggles the power supply or CE transitions from low to
high again. In other words, if the CCFL successfully starts
up then the start up time period will end before the one
second time period is up.
disconnected from SSV allowing capacitor C31 to float.
C3 is now the dominant cap on the SSC pin whereas C31
was the dominant cap during the initial startup period.
During steady state operation the SSC pin and C3 are
used to set the blanking period. This operation is de-
scribed more completely below.
connected to FCOMP, is also discharged and the voltage
at FCOMP is zero. The voltage at FCOMP controls the
frequency at which the FETs are driven. When FCOMP
is zero the frequency is at its maximum value. When
FCOMP reaches 5V then the switching frequency is at
its minimum value. The exact relation between the volt-
age at FCOMP and oscillator frequency is described more
fully in the detailed description of the oscillator circuitry.
so the switching frequency is at its maximum value. It is
intended that this maximum frequency is significantly
above the resonant frequency of the tank circuit made up
of the transformer and CCFL load. In this way the voltage
at the CCFL is lower than would be expected if the circuit
was driven nearer to its resonant frequency. At this point
in the operation of the circuit we assume that the CCFL
has not struck an arc and therefore appears as an open
circuit to the transformer. After the tube has struck the
voltage at the transformer output is controlled by the IV
relationship of the CCFL. Without the variable frequency
drive available with the AME9003 the user is unable to
control the voltage across the CCFL before the CCFL
strikes and current starts flowing in the CCFL.
the following conditions:
After the initial startup period pin SSC1ST is internally
At the beginning of the start up period capacitor C32,
At the beginning of start up mode FCOMP is zero volts
Capacitor C32 is charged by a 1uA current source with
a) If OVPL < 2.5V the charging current is 1uA and
the voltage at FCOMP ramps positive.
b) If OVPL > 2.5V and OVPH < 3.3V then the charg-
ing current is zero and the voltage at FCOMP re-
mains the same.
c) If OVPH > 3.3V then FCOMP is discharged to
approximately 1V, SSV is also driven to VSS.
CCFL Backlight Controller