MAX8759EVKIT Maxim Integrated Products, MAX8759EVKIT Datasheet - Page 26
![no-image](/images/manufacturer_photos/0/4/417/maxim_integrated_products_sml.jpg)
MAX8759EVKIT
Manufacturer Part Number
MAX8759EVKIT
Description
Display Modules & Development Tools MAX8759 KIT MAX8759 KIT
Manufacturer
Maxim Integrated Products
Datasheet
1.MAX8759ETI.pdf
(32 pages)
Specifications of MAX8759EVKIT
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Low-Cost, SMBus, CCFL Backlight Controller
The value in this read-write register reflects the highest
possible brightness value the inverter can set based on
inputs from the ALS. Users can change this value so
that they can control the effect of ALS. A write-byte
cycle to register 0x06 sets the highest possible bright-
ness value that can be set based on ALS inputs. If the
The MAX8759 requires four external n-channel power
MOSFETs: NL1, NL2, NH1, and NH2 to form a full-
bridge inverter circuit. The controller senses the on-state
drain-to-source voltage of the two low-side MOSFETs
NL1 and NL2 to detect the transformer primary current,
so the R
instance, if dual MOSFETs are used to form the full
bridge, NL1 and NL2 should be in one package. Since
the MAX8759 uses the low-side MOSFET R
primary overcurrent protection, the lower the MOSFET
R
the user should select a dual logic-level n-channel
MOSFET with low R
and keep the primary current limit at a reasonable level.
The regulator uses ZVS to softly turn on each of four
switches in the full bridge. ZVS occurs when the exter-
nal power MOSFETs are turned on when their respec-
tive drain-to-source voltages are near 0V (see the
Resonant Operation section). ZVS effectively eliminates
the instantaneous turn-on loss of MOSFETs caused by
C
capacitance discharge, and improves efficiency and
reduces switching-related EMI.
The MAX8759 senses the lamp current flowing through
sense resistors connected between the low-voltage ter-
26
ALSHL[7..0]: The highest brightness setting that can be set based on ALS inputs.
DS(ON)
OSS
BIT 7 (R/W)
ALSHL7
______________________________________________________________________________________
(drain-to-source capacitance) and parasitic
ALS High-Limit Register [0x06] (POR = 0xFF)
DS(ON)
, the higher the current limit. Therefore,
Applications Information
of NL1 and NL2 should be matched. For
BIT 6 (R/W)
ALSHL6
DS(ON)
Setting the Lamp Current
to minimize conduction loss,
BIT 5 (R/W)
ALSHL5
MOSFETs
DS(ON)
BIT 4 (R/W)
ALSHL4
for
BIT 3 (R/W)
brightness setting due to ALS is higher than the value
written to this register, the inverter immediately decreas-
es the brightness setting to the newly written value. A
read-byte cycle to register 0x06 returns the current
maximum brightness value that can be set based on
ALS inputs. The default value of register 0x06 is 0xFF,
which corresponds to the maximum brightness.
minals of the lamps and ground. The voltages across
the sense resistors are fed to IFB1 and IFB2 and are
internally full-wave rectified. The MAX8759 controls the
desired lamp current by regulating the average of the
rectified IFB_ voltages. To set the RMS lamp current in
a single-lamp application, determine the value of the
sense resistor as follows:
where I
785mV is the typical value of the IFB1 regulation point
specified in the Electrical Characteristics table. To set
the RMS lamp current to 6mA, the value of the sense
resistor should be 148Ω. The closest standard 1%
resistors are 147Ω and 150Ω. The precise shape of the
lamp-current waveform, which is dependent on lamp
parasitics, influences the actual RMS lamp current. Use
a true RMS current meter to make final adjustments.
The MAX8759 limits the transformer secondary voltage
during startup and lamp-out faults. The secondary volt-
age is sensed through the capacitive voltage-divider
formed by C4 and C5 (Figure 1). The VFB voltage is
proportional to the CCFL voltage. The selection of the
parallel resonant capacitor C1 is described in the
Transformer Design and Resonant Component
Selection section. C4 is usually between 10pF and
22pF. After the value of C4 is determined, select C5
ALSHL3
LAMP(RMS)
Setting the Secondary Voltage Limit
BIT 2 (R/W)
R
1
ALSHL2
=
2 2
is the desired RMS lamp current and
π
×
×
I
LAMP RMS
785
BIT 1 (R/W)
mV
ALSHL1
(
)
BIT 0 (R/W)
ALSHL0