APD192G0880005S51 Vishay, APD192G0880005S51 Datasheet - Page 2

• Manufacturer Part Number: APD192G0880005S51
• Description: Plasma Displays 192 x 88 Module
• Manufacturer: Vishay
• Type: Drive/Infrared Touch Screenr

Specifications of APD192G0880005S51

• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

INTERFACING
PARALLEL INTERFACE
The parallel interface offers two forms of hand-shaking called
Ready and Data Taken. Each 8 bit word
appearing on the data bus is latched with the falling edge of
the Data Strobe pulse.
This same negative transition notifies the on-board proces-
sor that data has been entered. The Ready signal then goes
low and the Data Taken signal goes low momentarily. The
Ready signal remains low until the command is completed or
the data has been entered. The Data Taken pulse is normally
800 nanoseconds long and indicates when the on-board
processor has read the input latch. Data may be entered into
the input latch after the rising edge of Data Taken.
SERIAL RS-232C INTERFACE
(See J4 pin descriptions.) The controller is considered to be
a DTE type device and will operate with a host that is either a
DTE or DCE type device. The serial input and output lines
meet RS-232C specifications. Serial data is entered asyn-
chronously with selectable baud rates. The byte format is 1
start bit, 8 data bits and 1 stop bit.
Document Number: 37048
Revision 05-Dec-00
* Indicates power up condition.
ORDERING INFORMATION
DESCRIPTION
Display, Drive Electronics, Controller Board (Includes DC/DC converter) ....................................................................... APD-192G088
Parallel Data Connector Kit................ .............................................................................................................................. ......280105-01
Power Connector Kit ......................................................................................................................................................... ......280108-04
Non-Glare Filter (amber circular polarized) - other filters available - contact factory ....................................................... ......280109-06
CONTROL CODES
Cursor Home
Carriage Return
Cursor Down (Line Feed)
Cursor Up
Cursor Right
Cursor Left
Alter Cursor Character Position
Cursor Character Address (0-1F)
Alter Cursor Row Position
Cursor Row Address (0-A)
Cursor On
Cursor Off
Clear Screen
Character Insert
Character Delete
Line Insert
Line Delete
ESCAPE CONTROL CODES
Erase to End of Line
Erase to End of Screen
Erase Line
Erase Line and Carriage Return
Alter Brightness
0 = Brightest
7 = Dimmest
Scroll
*End Scroll
Blank Display (on/off alternately)
Enter Bit Plot Mode
*Exit Bit Plot Mode
Reset Controller (to initial state)
ABRIDGED FUNCTION SUMMARY
1B,0D
1B,0C
1B,1A
1B,18
1B,13
1B,25
1B,20
1B,11
1B,16
1B,17
1B,19
HEX
0E
0D
0A
0B
0C
0F
09
08
11
13
##
12
14
10
16
17
##
##
ESC CNTRL M
ESC CNTRL Q
ESC CNTRL W
ESC CNTRL X
ESC CNTRL S
ESC CNTRL V
ESC CNTRL Y
ESC CNTRL L
ESC CNTRL Z
ESC SHIFT %
CNTRL P
CNTRL V
ESC SPACE
CNTRL W
CNTRL M
CNTRL Q
CNTRL R
CNTRL O
CNTRL N
CNTRL K
CNTRL H
CNTRL S
CNTRL T
CNTRL J
CNTRL L
CNTRL I
ASCII
PIN DESCRIPTION
CONNECTOR PIN
J1
J3
J4
(Pins 6, 8, and 20 of J4 are connected together internally.)
NOTE: Unidentified pins are not connected.
WARNING: Wrong connections or reversing J3 may cause
permanent damage to the display and host interface.
1
2
3
4
1,2,4,5, DB7-DB0 Data bus lines used transfer
7,6,3,9
13
15
17
22
10
16
12
25,26
19,20
3
2
4
7
SIGNAL
+ 12 VDC Panel supply voltage.
+ 5 VDC
GND
NC
READY
DATA
STROBE valid data is present on the
DATA
TAKEN
SYSTEM Used as a unique unit select
SELECT
CURSOR
DISABLE cursor. (This can also be
INITIALIZE Serves as a display reset. A
RESERVEDThis pin is to be left
+ 5 VDC
GND
RECEIVE The display receives data on
DATA
TRANSMITThe display transmits received
DATA
READY TOThis pin will be low when the
SEND
GND
DESCRIPTION
Logic supply voltage.
Ground.
No Connection.
data and commands to display.
Used to monitor the display's
activity. A logic 0 indicates that
the display is busy and cannot
respond to new data.
Used to notify the display that
data bus. The data byte is
loaded with the falling edge
of DATA STROBE.
This output goes to logic 0 for
approximately 800 nsec when
the display has accepted the
input data byte after DATA
STROBE goes low. New data
may be presented coincident
with the leading edge of this
signal.
input. A logic 0 on this line
disables the DATA STROBE
input.
accomplished with a data bus
command.)
logic 0 will initialize the
controller to its power up state.
Logic supply voltage.
Ground.
this pin. (The signal originates
at the DCE device transmit pin
2.)
data on this pin. (The signal
originates at the DCE device
receive pin 3.)
display is busy and cannot
accept new data. (This pin is
connected to pin 5 of the DCE
device.)
Signal ground (required).
A logic 1 will disable the visual
unconnected.
APD-192G088
PART NUMBER
Vishay Dale
www.vishay.com
3