D-436-52 Tyco Electronics, D-436-52 Datasheet - Page 3

• Manufacturer Part Number: D-436-52
• Description: CONN SPLICE BUTT 16-24AWG BLUE
• Manufacturer: Tyco Electronics
• Series: D-436r

Specifications of D-436-52

• Terminal Type: Butt Splice, Inline, Individual Openings
• Number Of Wire Entries: Varies by Wire Size
• Termination: Crimp
• Wire Gauge: 16-24 AWG
• Insulation: Fully Insulated
• Features: Heat Shrink
• Color: Blue, Blue Stripe
• Connector Type: Butt Splice
• Insulator Color: Blue
• Termination Method: Crimp
• Wire Size (awg): 20-16
• Contact Material: Copper
• Contact Plating: Tin
• Insulator Material: PVDF
• Chemical Resistant: No
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 5-1195133-1; 650139-000

APPLICATION
1. These parts are designed to provide an immersion resistant in-line splices of 2 or 3 to 1 wires falling within
2. Parts are available only as an assembly of one of each Item #1 and Item #2.
3. Parts are to be installed per Thermofit Assembly Procedure, see below.
4. Inside diameter and outside diameter of splice are to be measured in crimp areas, 2.54 to 5.08 (0.100 to 0.200)
5. Acceptance sampling shall be in accordance with Paragraph 4.6.1 of MIL-T-7928.
6 . Packing and packaging shall be in accordance with Section 5, Level C, of MIL-T-7928.
7. This document takes precedence over documents referenced herein.
1.0
2.0
3.0
UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN MILLIMETERS.
INCHES DIMENSIONS ARE BETWEEN BRACKETS.
TOLERANCES:
0.00 N/A
0.0 N/A
0 N/A
DRAWN BY:
If this document is printed it becomes uncontrolled. Check for the latest revision.
from ends of part. Slight burr permitted on parted surfaces.
the size range listed on sheet 1, having insulations rated for at least 135 C.
M. FORONDA
SCOPE
This document outlines the procedure to be followed to obtain immersion resistant 3 or 2 to 1 in-line splices using
Thermofit In-Line Splice Sealing System D-436-52/-53.
PROCEDURE:
a) Strip all wires 7.92 (0.312) to 8.74 (0.344).
b) Attach the single lead to the appropriate size crimp splice using a Raychem AD-1377 Crimp Tool.
c) Pass the wires to be attached to other barrel through the sealing sleeve from the three-hole insert end.
d) Insert wires into barrel and crimp. Care must be taken that the wires remain untwisted between the crimp
e) Apply heat, using the recommended heat source, first to the three-hole insert and then the other. Heat should
RECOMMENDED RAYCHEM HEATING TOOLS
Thermogun #500A
Shop Air Heater #CV-4504
Mini-Gun #CV-5300
Heater
splice and the three wire seal or the sealing sleeve cannot be positioned properly.
be applied until insert melts and flows axially along the wires.
ANGLES: N/A
ROUGHNESS IN
MICRON
Menlo Park, CA 94025, USA
Tyco Electronics Corporation
REPLACES:
305 Constitution Drive
Tyco Electronics reserves the right to amend
this drawing at any time. Users should evaluate
the suitability of the product for their
application.
N/A
SPECIFICATION CONTROL DRAWING
THERMOFIT ASSEMBLY PROCEDURE
DCR NUMBER:
D001302
Raychem
Products
Reflector
TG-14
991180
991319
TITLE :
DOCUMENT NO.:
DATE:
PROD. REV.
SEE TABLE
IN-LINE SPLICE SEALING SYSTEM,
Color Coded, with Inspection Slots
2 OR 3 TO 1 SPLICE: Tin Plated,
05-Dec.-00
D-436-52/-53
SCALE:
None
SIZE:
A
DOC ISSUE:
SHEET:
1
3 of 3