M39006/22-0345H Kemet, M39006/22-0345H Datasheet - Page 3

• Manufacturer Part Number: M39006/22-0345H
• Manufacturer: Kemet

Specifications of M39006/22-0345H

• Tolerance (+ Or -): 10%
• Voltage: 50VDC
• Mounting Style: Through Hole
• Operating Temp Range: -55C to 125C
• Esr: 5.31Ohm
• Construction: Axial
• Df: 4%
• Dcl: 1uA
• Seal: Hermetic
• Insulation: Sleeved
• Polarity: Polar
• Failure Rate: P
• Product Length (mm): 12.5mm
• Product Depth (mm): Not Requiredmm
• Product Height (mm): Not Requiredmm
• Product Diameter (mm): 5.56mm
• Capacitance: 10uF
• Lead Free Status / RoHS Status: Supplier Unconfirmed

Introduction
the initial “T”, followed by a “Series” number. T19X des-
ignates commercial product; T29X is military grade in
accordance with Military Specification, MIL-PRF-
39006. For detailed performance characteristics of the
T29X series, please refer to the latest issue of the
Military Specification. MIL-PRF-39006 establishes
1000 hour failure rate levels of 1%, 0.1%, and 0.01%.
T29X series components are available in M, P, and R
failure rates (1.0, 0.1, and 0.01, respectively).
tive Product Series in this catalog. All Military products
are 100% electrically screened for the
shown in the respective product section. For non-mili-
tary product, all series are 100% screened for leakage,
capacitance and dissipation factor. All Series are
inspected to electrical limits using a minimum .1% AQL
sampling plans, according to the Military Standard MIL-
STD-105, even after 100% testing. This sampling plan,
to the best of KEMET Electronics’ knowledge, meets or
exceeds the generally accepted industry standard for
similar products. KEMET capacitors may also be sup-
plied, with prior agreement, to meet specifications with
requirements differing from those of KEMET catalogs.
talum capacitors and illustrate typical performance
under normal application conditions, except where
noted. The intent of these Notes is to provide general-
ized information concerning performance characteris-
tics.
1. General Application Class
cuits where the AC component is small compared to
the DC component. Typical uses known to KEMET
Electronics include blocking, by-passing, decoupling,
and filtering. They are also used in timing circuits. If two
of these polar capacitors are connected “back-to-back”
(i.e., negative-to-negative or positive-to-positive), the
pair may be used in AC applications (as a non-polar
device).
2. Storage Conditions
over the operating temperature range specified in the
catalogs for each Series. The range is from -55 to
+125°C for all Series.
temporary increase in leakage current (measured
under standard conditions), but the original value is
usually restored within a few minutes after application
of rated voltage.
combination of high temperature and high humidity, but
is normally restored by voltage conditioning under
standard conditions. The increase will be greater than
that experienced under temperature influence alone
because of conduction through absorbed water.
KEMET wet tantalum capacitors are identified by
Specific requirements are set forth in the respec-
These Notes apply generally to all KEMET wet tan-
Wet tantalum capacitors are usually applied in cir-
Capacitors may be stored without applied voltage
Storage at high temperature may cause a small,
DC leakage current may rise upon exposure to a
© KEMET Electronics Corporation, P.O. Box 5928, Greenville, SC 29606 [phone]
parameters
on external insulating surfaces. The water film may also
attract a layer of dust from the air increasing the effect.
The most sensitive parameter is leakage current.
3. Polarity
may be permanently damaged or destroyed if connect-
ed with the wrong polarity. The positive terminal is iden-
tified on the capacitor body by a polarity mark and the
capacitor body may include an obvious geometrical
shape. See paragraph 11 for Reverse Voltage capabil-
ities.
4. Operating Environment
will apply also when capacitors are operated within the
applicable electrical ratings described below. The tem-
porary increase in leakage current (at standard condi-
tions) following elevated-temperature exposure is not
observed, however, if the capacitors are operated with
adequate DC voltage applied.
5. Capacitance
up to 1 volt rms applied. Measured circuits are of high
impedance, however, and under these conditions 1 volt
rms may be applied even to 6 volt capacitors (23%
peak reversal) without a DC dias. DC bias is thus nor-
mally not used, except when rated voltage is below 6
volts and the AC signal level exceeds 0.3 vrms.
However, MIL-PRF-39006 provides for up to 2.2 volts
DC. DC bias is not commonly used at room tempera-
ture, but is more commonly used at elevated tempera-
tures.
up to about 2% when full rated voltage is applied as
bias. DF is also reduced by the presence of DC.
decreases more noticably at higher frequencies. Larger
capacitance values decline more rapidly than small rat-
ings.
according to the curve of Figure 1.
Figure 1. Typical Effect of Temperature upon
Capacitance
This Series may be affected by absorption of water
These capacitors are inherently polar devices and
Most of the discussion under “Storage Conditions”
Capacitance is measured at 120 Hz and 25°C with
DC bias causes a small reduction in capacitance,
Capacitance changes very little below 1 kHz but
Capacitance typically changes with temperature
Performance Characteristics
3