TZ03R300T169A00 Murata, TZ03R300T169A00 Datasheet - Page 32

• Manufacturer Part Number: TZ03R300T169A00
• Manufacturer: Murata
• Type: Ceramicr

Specifications of TZ03R300T169A00

• Capacitance Range (min/max) (pf): 5.2/30
• Tolerance (+ Or -): 0% to 50%
• Voltage: 100VDC
• Temp Coeff (dielectric): N750±300 ppm/°C
• Operating Temp Range: -25C to 85C
• Mounting Style: Through Hole
• Construction: Top Adj
• Q: 500
• Failure Rate: Not Required
• Product Length (mm): 6mm
• Product Depth (mm): 6mm
• Product Height (mm): 4.8mm
• Product Diameter (mm): Not Requiredmm
• Lead Free Status / RoHS Status: Compliant

!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
1. Do not use the trimmer capacitor under atmosphere
2. Before using trimmer capacitor, please store under
3. Do not store in or near corrosive gasses.
4. Use within 6 months of delivery.
5. Do not store under direct sunlight.
1. Soldering
(1) Can be soldered by reflow soldering method, flow
(2) Soldering condition
(3) The amount of solder is critical.
(4) The thickness of solder paste should be printed
(5) When using soldering iron, the string solder
(6) Our recommended chlorine content of solder is
(7) Do not use water-soluble flux (for water
Notice (Storage and Operating Condition)
of RTV silicone rubber (Room Temperature
Vulcanizing Silicone Rubber) except Acetone
liberating silicone sealant.
the condition of -10 to +40 degree C and 30 to
85%RH.
Notice (Soldering and Mounting)
(a) Solder paste: 0.2wt% max.
(b) String solder: 0.5wt% max.
soldering method, and soldering iron.
Refer to the temperature profile.
If the soldering conditions are not suitable, e.g.,
excessive time and/or excessive temperature, the
trimmer capacitor may deviate from the specified
characteristics.
from 150 micro m to 200 micro m and the dimension
of land pattern should be Murata's standard land
pattern used at reflow soldering. Insufficient
amounts of solder can lead to insufficient
soldering strength on PCB. Excessive amounts of
solder may cause bridging between the terminals
or contact failure due to flux wicking up.
shall be applied to the lower part of the
terminal only. Do not apply flux except to the
terminals. Excessive amounts of solder and/or
applying solder to the upper part of the
terminal may cause fixed rotor or contact failure
due to flux invasion into the movable part and/or
the contact point. The soldering iron should not
come in contact with the plastic case of the
trimmer capacitor. If such contact does occur,
the trimmer capacitor may be damaged.
as follows.
cleaning). To prevent the deterioration of
trimmer capacitor characteristics, apply flux
only to terminals.
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
6. Do not use the trimmer capacitor under the
2. Mounting
3. Cleaning [with cover film type]
4. Other
(1) Corrosive gasses atmosphere
(2) In liquid (ex. water, oil, medical liquid,
(3) Dusty / dirty atmosphere
(4) Direct sunlight
(5) Static voltage nor electric/magnetic fields
(6) Direct sea breeze
(7) Other variations of the above
(1) Do not apply excessive force (preferably 5.0N
(2) Do not warp and/or bend PCB to prevent trimmer
(3) Use the suitable PCB holes which are the same
(4) Do not apply bending stress more than 10.0N
(5) Mount trimmer capacitor in contact with PCB
(6) In case of bending the terminals, do not apply
(7) Use the suitable dimension of the pick-up nozzle.
conditions listed below.
Isopropyl-alcohol and Ethyl-alcohol are applicable
solvents for cleaning. If you use any other types of
solvents, please evaluate performance by your set.
Moreover, please confirm no damage for trimmer
capacitor after cleaning by your conditions.
Note the polarity of the trimmer capacitor to
minimize influence by stray capacitance.
(Refer to the dimensions concerning the polarity.)
(ex. Chlorine gas, Hydrogen sulfide gas,
Ammonia gas, Sulfuric acid gas, Nitric oxide gas,
etc.)
organic solvent, etc.)
[Ref: 500gf] max.), when the trimmer capacitor
is mounted on the PCB.
capacitor from breakage.
pitch as the terminal of the trimmer capacitor.
If it would not fit with the terminal, the
excessive stress would be applied to the
terminal and the trimmer capacitor may deviate
from the specified characteristics (Terminal
shape C and D).
(Ref: 1kgf) after the trimmer capacitor has
been mounted on the PCB (Terminal shape C and D).
(Terminal shape C and D).
excessive force to the body of the product and
prevent the terminal fixing part from damaging.
> Without cover film type
> With cover film type
- External dimensions of 4.5x4.0mm and
- 4.0mm external diameter and 2.0mm bore
2.5mm bore diameter.
diameter.
31
T13E.pdf
07.3.1
7