6116317-6 TE Connectivity, 6116317-6 Datasheet - Page 3

• Manufacturer Part Number: 6116317-6
• Manufacturer: TE Connectivity
• Type: RJ-45r

Specifications of 6116317-6

• Positions Loaded: 128
• Number Of Contacts: 128POS
• Body Orientation: Right Angle
• Category Number: Cat 5
• Pitch (mm): 2.03mm
• Contact Material: Phosphor Bronze
• Operating Temp Range: -40C to 80C
• Current Rating (max): 1.5/ContactA
• Voltage Rating Max: 150VAC
• Housing Color: Black
• Product Height (mm): 22.99mm
• Product Depth (mm): 31.06mm
• Product Length (mm): 118.24mm
• Number Of Ports: 16Port
• Gender: F
• Mounting Style: Through Hole
• Contact Plating: Gold Over Nickel
• Housing Material: Polybutylene Terepht
• Product Type: Connector
• Jack Type: RJ45
• Pcb Mounting Orientation: Side Entry (Right Angle)
• Pcb Mount Style: Through Hole
• Termination Method To Pc Board: Through Hole - Press Fit
• Performance Category: Cat 5
• Number Of Contacts Loaded: 8
• Grounding Options: Panel Ground and PCB Ground
• Panel Stops: Without
• Keyed: No
• Profile: Very Low; Offset - Over Hangs PCB
• Color: Black
• Number Of Terminals Per Port: 8
• Shield Material: .010 [0.25] Copper Alloy
• Jack Configuration: 2 x 8
• Panel Mount Retention: Without
• Shielded: Yes
• Solder Tail Contact Plating: Tin over Nickel
• Grounding Clips: Without
• Port Configuration: Stacked
• Number Of Positions: 8
• Inverted Jack Face: No
• Led: With
• Shield Plating: Tin over Copper
• Number Of Pcb Ground Tabs: 11
• Pcb Tail Length (mm [in]): 4.35 [0.171]
• Grounding Tab Plating: Tin over Copper
• Preloaded: Yes
• Contact Plating, Mating Area, Material: Gold (50)
• Contact Base Material: Phosphor Bronze
• Pcb Action Pin Grounds: With
• Ul Flammability Rating: UL 94V-0
• Rohs/elv Compliance: RoHS compliant, ELV compliant
• Lead Free Solder Processes: Not relevant for lead free process
• Rohs/elv Compliance History: Always was RoHS compliant
• Led Color; Top Left: Green
• Led Color; Top Right: Yellow
• Led Color; Bottom Left: Green
• Led Color; Bottom Right: Yellow
• Pcb Thickness, Recommended (mm [in]): 1.57 [0.062]
• Lead Free Status / RoHS Status: Compliant

4.
4.1.
4.2.
4.3.
4.4.
Rev C
QUALITY ASSURANCE PROVISIONS
Qualification Testing
A.
B.
Requalification Testing
If changes significantly affecting form, fit or function are made to the product or manufacturing process,
product assurance shall coordinate requalification testing, consisting of all or part of the original testing
sequence as determined by development/product, quality and reliability engineering.
Acceptance
Acceptance is based on verification that the product meets the requirements of Figure 1. Failures
attributed to equipment, test setup or operator deficiencies shall not disqualify the product. When
product failure occurs, corrective action shall be taken and samples resubmitted for qualification.
Testing to confirm corrective action is required before resubmittal.
Quality Conformance Inspection
The applicable quality inspection plan will specify the sampling acceptable quality level to be used.
Dimensional and functional requirements shall be in accordance with the applicable product drawing
and this specification.
Sample Selection
Samples shall be prepared in accordance with applicable Instruction Sheets and shall be selected
at random from current production. Test group 1 shall consist of 10 terminated plugs/unmounted
jack pairs.
Test Sequence
Qualification inspection shall be verified by testing samples as specified in Figure 2.
108-1163-2
3 of 4