SFELA10M7EA00 Murata, SFELA10M7EA00 Datasheet - Page 99
![no-image](/images/manufacturer_photos/0/4/464/murata_sml.jpg)
SFELA10M7EA00
Manufacturer Part Number
SFELA10M7EA00
Description
Manufacturer
Murata
Datasheet
1.SFELA10M7EA00.pdf
(115 pages)
Specifications of SFELA10M7EA00
Rad Hardened
No
Lead Free Status / RoHS Status
Not Compliant
!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
1. Do not use this product with bend. The component
2. The component may be damaged when an excessive
3. All kinds of re-flow soldering must not be applied
4. Do not clean or wash the component as it is not
5. Please contact Murata or Murata representative for
6. Do not use strong acidity flux, more than 0.2wt%
1. The component will be damaged when an excessive
2. In the case that the component is cleaned, confirm
3. In case of covering filter with over coat,
4. Do not use strong acidity flux, more than 0.2wt%
1. Do not use this product with bend. The component
2. The component will be damaged when an excessive
3. All kinds of re-flow soldering must not be applied
4. Do not clean or wash the component as it is not
5. Do not use strong acidity flux, more than 0.2wt%
6. In case of covering filter with over coat,
may be damaged if excess mechanical stress is
applied to it mounted on the printed circuit board.
stress is applied.
on the component.
hermetically sealed.
soldering condition, in case of using lead free
solder.
chlorine content, in flow soldering.
stress is applied.
that no reliability degradation is created.
conditions such as material of resin, cure
temperature, and so on should be evaluated
carefully.
chlorine content, in re-flow soldering.
CERAFILr 3.5-6.5MHz Lead Type
CERAFILr 455kHz Chip Type SFPKA Series
CERAFILr 455kHz Lead Type
may be damaged if excess mechanical stress is
applied to it mounted on the printed circuit board.
stress is applied.
on the component.
hermetically sealed.
chlorine content, in flow soldering.
conditions such as material of resin, cure
temperature, and so on should be evaluated
carefully.
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
7. In case of covering filter with over coat,
8. Accurate test circuit values are required to
9. For safety purposes, connect the output of filters
5. The product, packed in the moisture-proof bag
6. For safety purposes, connect the output of filters
7. Accurate test circuit values are required to
8. For safety purpose, connect the output of filters
conditions such as material of resin, cure
temperature, and so on should be evaluated
carefully.
measure electrical characteristics. It may be a
cause of miscorrelation if there is any
deviation, especially stray capacitance, from the
test circuit in the specification.
to the IF amplifier through a D.C. blocking
capacitor. Avoid applying a direct current to the
output of ceramic filters.
(dry pack), is sensitive to moisture. The following
treatment is required before applying re-flow
soldering, to avoid package cracks or reliability
degradation caused by thermal stress. When unpacked,
store the component in an atmosphere of below 25
degree C and below 65%R.H., and solder within 48
hours.
to the IF amplifier through a D.C. blocking
capacitor. Avoid applying a direct current to the
output of ceramic filters.
measure electrical characteristics.
It may be a cause of miscorrelation if there is
any deviation, especially stray capacitance, from
the test circuit in the specification.
to the IF amplifier through a D.C. blocking
capacitor. Avoid applying a direct current to the
output of ceramic filters.
Notice (Handling)
97
P50E.pdf
08.1.29
27