Z4D-F04D Omron, Z4D-F04D Datasheet
Z4D-F04D
Specifications of Z4D-F04D
Related parts for Z4D-F04D
Z4D-F04D Summary of contents
Page 1
... Power and alarm indicator included in the H Z4D-F04A model Stability/operation indicator and distance H adjuster included in the Z4D-F04D model Numerous applications possible when the H analog output model is integrated with OMRON’s K3TX Intelligent Signal Processors ON/OFF output model (NPN open collector) ...
Page 2
... VAC for 1 min between current carry parts and case 0 max. ABS (Polycarbonate for the sensing part) Approx (without connector cable) 20 MΩ min. (at 500 VDC the sensor’s laser beam center. Although a sub-beam may be observed around the Z4D-F04A/D Z4D-F04D --- --- 40 µm --- --- NPN open collector VDC max max. ...
Page 3
... Displacement value Analog displace- ment output The response time of the sensor (Z4D-F04D): ON/OFF switching time 7. The value is at the sensing range of 4 mm. J TYPICAL APPLICATIONS Double Feed Detection Vibration Detection ...
Page 4
... Z4D-F04A/D Engineering Data J ANALOG OUTPUT MODEL (Z4D-F04A) Sensing Distance vs. Analog Output Characteristics (Typical) Sensing distance (mm) Angle Characteristics with Difference in Vertical Inclination Standard paper PBT SPCC Positive inclination Negative inclination Inclination angle (_) Angle Characteristics with Difference in Horizontal Inclination Standard paper PBT SPCC ...
Page 5
... Z4D-F04A/D J ON/OFF OUTPUT MODEL (Z4D-F04D) Sensing Distance vs. Adjuster Angle Characteristics Standard paper PBT SPCC Sensing distance (mm) Note: The PBT plastic referred in this data was detected under its natural state. Nomenclature J ANALOG OUTPUT (Z4D-F04A) (1) (2) (1) Power (PWR) Indicator The green PWR indicator is lit when power is applied to the sensor ...
Page 6
... Unit: mm (inch) J Z4D-F04A (1.26) Mounting bracket can be attached to this side. Receiver 25.5 (1.00) 5.9(0.23) 33.7 (1.33) 9.1(0.36) (0.05) 10.7(0.42) Emitter J Z4D-F04D (1.26) Mounting bracket can be attached to this side. Receiver 25.5 (1.00) 5.9(0.23) 33.7 (1.33) 9.1(0.36) (0.05) Emitter 6 NPN Open Collector Output VDC ...
Page 7
... Two, C1 1,000 13.5 (0.53) (39.37) 0.6 1.4 (0.06) (0.02) 2.5 (0.10) Z4D-F04A/D 7 ...
Page 8
... For details about the K3TX, refer to the K3TX Data- sheet. 4. The diagram shown here is for a K3TX model with DC power specifications. When using a K3TX with AC power specifications, separate the AC power supply to the K3TX from the DC power supply to the Z4D-F04A. 8 Z4D-F04D and S3D2 Brown Black Z4D - F04A Blue + ...
Page 9
... Z4D-F model may explode or burn. Load short-circuit Do not short-circuit the load, or the Z4D-F may explode or burn. Wiring Be sure to wire the Z4D-F correctly and be careful not to connect the polarities incorrectly. Failure to wire the Z4D-F correctly can result in safety hazards or damage to the equipment. Connection with no load ...
Page 10
... V respectively. If there is no sensing object or the reflectivity of the sensing object is low, the resulting analog output will be the standard upper limit. Analog Output Diagram Z4D-F04D ON/OFF Output Diagram The ON/OFF position can be set with the distance adjuster if a sensing object is at the sensing range (i.e., 4 ...
Page 11
... If pressure is applied to the cable alone, it will damage the lock mechanism inside the connector. J INTERFERENCE Z4D-F04A/D microdisplacement sensors can be installed within close proximity to each other and operate independently without interference (refer to the figures below). However, if they are installed at an oblique angle to each other, interference may result ...
Page 12
... One East Commerce Drive Schaumburg, IL 60173 1-800-55-OMRON Cat. No. GC APMS-1 09/02 12 OMRON ON- -LINE Global -- http://www.omron.com USA -- http://www.omron.com/oei Canada -- http://www.omron.com/oci Specifications subject to change without notice. Z4D-F04A/D OMRON CANADA, INC. 885 Milner Avenue Toronto, Ontario M1B 5V8 416-286-6465 Printed in U.S.A. ...