MAX44264EVKIT# Maxim Integrated Products, MAX44264EVKIT# Datasheet - Page 2
![no-image](/images/manufacturer_photos/0/4/417/maxim_integrated_products_sml.jpg)
MAX44264EVKIT#
Manufacturer Part Number
MAX44264EVKIT#
Description
Amplifier Modules & Development Tools Ultra-Low Power Op A mp in a Tiny 6-Bump
Manufacturer
Maxim Integrated Products
Datasheet
1.MAX44264EVKIT.pdf
(7 pages)
Specifications of MAX44264EVKIT#
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
•
•
•
The EV kit is fully assembled and tested. Follow the steps
below to verify board operation. Caution: Do not turn on
the power supply until all connections are completed.
1) To configure the EV kit as an op-amp buffer to
2) Set the power supply to provide 5V and then disable
3) Connect the power-supply positive terminal to the
4) Connect the power-supply ground to the GND PCB
5) Enable the power supply.
6) Verify that the OUT PCB pad is at 2.5V.
The MAX44264 EV kit contains the MAX44264 IC, which
is a rail-to-rail micropower op amp with an ultra-low
750nA supply current designed in a 6-bump WLP. The
EV kit operates from a single 1.8V to 5.5V DC power
supply.
Table 1. Default Shunt Positions
JUMPER
Detailed Description of Hardware
balance super capacitors C1 and C2 charge, set
jumpers JU1, JU2, and JU3 in their default positions,
as shown in Table 1.
the power supply.
VDD PCB pad.
pad (nearest the VDD PCB pad).
JU1
JU2
JU3
MAX44264 EV kit
1.8V to 5.5V, 100mA DC power supply
Voltmeter
Not installed
POSITION
Installed
SHUNT
2-3
_________________________________________________________________ Maxim Integrated Products 2
IN- = OUT (through resistor R2)
Required Equipment
DESCRIPTION
IN+ = VDD/2
Quick Start
Procedure
The EV kit comes preconfigured as a buffer used in a
super-capacitor charge-balancing circuit. Super capaci-
tors offer exceptional charge storage density and are
widely used to prolong the life of weak batteries sub-
ject to high current-load pulses, or to buffer a weak
energy source to a high-power load in energy-harvesting
devices. In such applications, it is common to have a
stack of super capacitors connected in series to achieve
the desired working voltage. The EV kit demonstrates
an active, super-capacitor charge-balancing circuit that
distributes the charge equally across two series-connected
super capacitors (C1 and C2), ensuring identical voltage
across each capacitor. This circuit prevents overvoltage
conditions from occurring across either of the super
capacitors due to a difference in leakage currents and
tolerance in the capacitor values. The IC’s ultra-low power
consumption of 750nA and CMOS inputs allow a power-
efficient solution to the super-capacitor charge-balancing
problem.
While super-capacitor charge balancing is the featured
application, the EV kit also provides flexibility to easily
reconfigure the op amp into any of the four common
circuit topologies: inverting amplifier, noninverting ampli-
fier, differential amplifier, or buffer. Table 2 lists the JU1,
JU2, and JU3 jumper settings for the various op-amp
configurations. The configurations are described in the
next few sections.
Important Note: Remove super capacitors C1 and
C2 when not demonstrating super-capacitor charge
balancing in the four configurations detailed in the
Noninverting Amplifier, Inverting Amplifier, Differential
Amplifier, and Buffer Amplifier sections.
Table 2. JU1, JU2, JU3 Jumper Functions
(IN-, IN+, REF)
CONFIGURATION
Super-capacitor
Noninverting
Differential
OP-AMP
Inverting
Evaluates: MAX44264
Buffer
buffer
Installed
installed
installed
Default Application Circuit
JU1
Not
Not
Op-Amp Configurations
SHUNT POSITION
JU2
1-2
2-3
Installed
installed
JU3
Not