2180-DEMO THAT Corporation, 2180-DEMO Datasheet - Page 8

no-image

2180-DEMO

Manufacturer Part Number
2180-DEMO
Description
Audio Modules & Development Tools Pre-Trimmed VCA Demo Board
Manufacturer
THAT Corporation
Datasheet

Specifications of 2180-DEMO

Description/function
Audio Amplifiers
Operating Supply Voltage
15 V
Product
Audio Modules
For Use With/related Products
THAT2180
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Document 600029 Rev 02
the familiar ratio of R
determine the overall voltage gain when the 2180 is
set for 0 dB current gain. Since the VCA performs
best at settings near unity gain, use the input and
feedback resistors to provide design-center gain or
loss, if necessary.
opamp is needed to cancel the output capacitance of
the VCA. Without it, this capacitance will destabilize
most opamps. The capacitance at pin 8 is typically
15 pF.
Power Supplies
Positive
(pin 7). No special bypassing is necessary, but it is
good practice to include a small (~1 μF) electrolytic
or (~0.1 μF) ceramic capacitor close to the VCA IC
on the PCB. Performance is not particularly depend-
ent on supply voltage. The lowest permissible supply
voltage is determined by the sum of the input and
output currents plus I
through the output of the internal transconductance
amplifier and down through the core and voltage bias
generator. Reducing signal currents may help accom-
modate low supply voltages. THAT Corporation
intends to publish an application note covering
operation on low supply voltages. Please inquire for
its availability.
the process characteristics and internal power
consumption. +18 V is the nominal limit.
Negative
normal negative supply pins, this point is intended to
be connected to a current source I
a resistor to V
able for the device. As mentioned before, this source
must supply the sum of the input and output signal
currents, plus the bias to run the rest of the IC. The
minimum value for this current is 570 μA over the
sum of the required signal currents. Usually, I
should equal 2.4 mA for most pro audio applications
with ±15 V supplies. Higher bias levels are of limited
value, largely because the core transistors become
ineffective at logging and antilogging at currents over
1 mA.
A small feedback capacitor around the output
The positive supply is connected directly to V+
The highest permissible supply voltage is fixed by
The negative supply terminal is V- (pin 5). Unlike
Mathematically, this can be expressed as
I
CELL
≥ Peak (I
EE
), which determines the current avail-
IN
) + Peak (I
f
/R
SET
Tel: +1 508 478 9200; Fax: +1 508 478 0990; Web: www.thatcorp.com
i
THAT Corporation; 45 Sumner Street; Milford, MA 01757-1656; USA
for an inverting opamp will
, which must be supplied
OUT
) + 220 μA; and
SET
(usually simply
Copyright © 2008, THAT Corporation
SET
Page 8 of 12
below ground, which, for the 2180, is approximately
-2.85 V. Since this pin connects to a (high
impedance) current supply, not a voltage supply,
bypassing at pin 5 is not normally necessary.
Ground
ence for the VCA. The non-inverting input of the
internal opamp is connected here, as are various
portions of the internal bias network. It may not be
used as an additional input pin.
Voltage Control
Negative Sense
This point controls gain inversely with applied
voltage: positive voltage causes loss, negative voltage
causes gain. As described on Page 5, the current gain
of the VCA is unity when pin 3 is at 0 V with respect
to pin 2, and varies with voltage at approximately
-6.1 mV/dB, at room temperature.
Positive Sense
sense voltage control port. A typical circuit using this
approach is shown in Figure 14. E
grounded,
low-impedance voltage source. Using the opposite
sense of control can sometimes save an inverter in
the control path. In order to maintain the wafer level
adjustment which minimizes THD, leave pin 4 open.
IN
I
I
The voltage at V- (pin 5) is four diode drops
The GND pin (pin 6) is used as a ground refer-
E
As mentioned earlier, E
CELL
SET
Power Supplies
C-
Vcc = +15 V
Vee = -15 V
Figure 14. Positive control port using Pin 2 (E
≥ Peak (I
(pin 3) is the negative voltage control port.
10u
= I
SET
and
- 350 μA. Therefore,
Series
2180
20k
VCA
IN
5.1k
) + Peak (I
E
Vee
C+
1
Vcc
Blackmer® Pre-trimmed IC VCAs
7
V+
-IN
V-
GND
5
Ec+
6
(pin
Ec-
Ec+
3
SYM
2
NC
4
C+
OUT
OUT
8
(pin 2) is the positive-
) + 570 μA.
2)
C-
driven
THAT 2180 Series
(pin 3) should be
-
+
OP275
22p
20k
from
C+
)
OUT
a

Related parts for 2180-DEMO