MAX16920BEVKIT+ Maxim Integrated Products, MAX16920BEVKIT+ Datasheet - Page 2

• Manufacturer Part Number: MAX16920BEVKIT+
• Description: Power Management Modules & Development Tools Multiple-Output Auto omotive Power Supply
• Manufacturer: Maxim Integrated Products

Specifications of MAX16920BEVKIT+

• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Note: Indicate that you are using the MAX16920B when contacting these component suppliers.
• MAX16920B EV kit
• 12V, 2.5A DC power supply
• Four electronic loads (e.g., HP6060B)
• Four voltmeters
The EV kit is fully assembled and tested. Follow the steps
below to verify board operation. Caution: Do not turn on
power supplies until all connections are completed.
1) Verify that all jumpers are in their default position, as
2) Adjust the power supply to 12V and connect to the
3) Adjust the first load to 150mA and connect to the
4) Connect the first voltmeter to the OUT1 and PGND1
ADDITIONAL COMPONENTS FOR MAX16920A
EVALUATION
Cooper Bussmann
Diodes Incorporated
Murata Electronics North America, Inc.
Panasonic Corp.
TDK Corp.
Vishay
DESIGNATION
shown in Table 1.
VIN and PGND PCB pads on the EV kit.
OUT1 and PGND1 PCB pads on the EV kit.
PCB pads on the EV kit.
U1
—
—
—
_________________________________________________________________ Maxim Integrated Products 2
QTY
10
1
1
3
SUPPLIER
Power-management IC
(32 TQFN-EP)
Maxim MAX16920BATJ/V+
Shunts
PCB: MAX16920B EVALUATION
KIT+
22FF Q10%, 10V X7R ceramic
capacitors (1206)
Murata GRM31CR71A226K
Required Equipment
DESCRIPTION
Evaluates: MAX16920A/MAX16920B
Quick Start
Procedure
916-941-1117
805-446-4800
770-436-1300
800-344-2112
847-803-6100
402-563-6866
PHONE
5) Adjust the second load to 600mA and connect to the
6) Connect the second voltmeter to the OUT2 and
7) Adjust the third load to 1.5A and connect to the OUT3
8) Connect the third voltmeter to the OUT3 and PGND3
9) Adjust the fourth load to 150mA and connect to the
10) Connect the fourth voltmeter to the OUTA and GND
11) Connect the SYNC and GND PCB pads on the EV kit
12) Turn on the DC power supply.
13) Enable all loads.
14) Verify that the first voltmeter reads approximately 3.3V.
15) Verify that the second voltmeter reads approximately 5V.
16) Verify that the third voltmeter reads approximately 3.3V.
17) Verify that the fourth voltmeter reads approximately 5V.
DESIGNATION
OUT2 and PGND2 PCB pads on the EV kit.
PGND2 PCB pads on the EV kit.
and PGND3 PCB pads on the EV kit.
PCB pads on the EV kit.
OUTA and GND PCB pads on the EV kit.
PCB pads on the EV kit.
together.
—
—
—
—
Component List (continued)
www.cooperet.com
www.diodes.com
www.murata-northamerica.com
www.panasonic.com
www.component.tdk.com
www.vishay.com
QTY
1
1
1
1
Component Suppliers
47FF Q10%, 10V X7R ceramic
capacitor (1210)
Murata GRM32ER71A476K
47FH, 1.14A inductor
(7.60mm x 7.60mm x 4.35mm)
Cooper Bussmann DRA74-470-R
22FH, 1.68A inductor
(7.60mm x 7.60mm x 4.35mm)
Cooper Bussmann DRA74-220-R
10FH, 2.56A inductor
(7.60mm x 7.60mm x 4.35mm)
Cooper Bussmann DRA74-100-R
WEBSITE
DESCRIPTION