MAX17010EVKIT+ Maxim Integrated Products, MAX17010EVKIT+ Datasheet - Page 2

• Manufacturer Part Number: MAX17010EVKIT+
• Description: Power Management Modules & Development Tools MAX17010 EVAL KIT MAX17010 EVAL KIT
• Manufacturer: Maxim Integrated Products

Specifications of MAX17010EVKIT+

• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

MAX17010 Evaluation Kit
Note: Indicate that you are using the MAX17010 when contacting these component suppliers.
• 1.8V to 5.5V, 2A DC power supply
• Voltmeter
The MAX17010 EV kit is fully assembled and tested.
Follow the steps below to verify board operation.
Caution: Do not turn on the power supply until all
connections are completed.
1) Verify that there is a shunt installed across jumper
2) Verify that SW1 and SW2 eight-position DIP switch-
2
DESIGNATION QTY
Central Semiconductor Corp.
Fairchild Semiconductor
Murata Mfg. Co., Ltd.
Nihon Inter Electronics Corp.
SANYO North America Corp.
Sumida Corp.
TDK Corp.
Toshiba America Electronic Components, Inc.
D2, D3, D4
R2, R5, R6
JU1.
es are in the ON position.
_______________________________________________________________________________________
JU1
D1
R1
L1
1
3
1
1
1
3
SUPPLIER
30V, 1A Schottky diode (S-Flat)
Nihon EP10QY03
Toshiba CRS02(TE85L,Q)
100V, 200mA dual diodes (SOT23)
Fairchild MMBD4148SE
(Top Mark: D4)
Central CMPD7000 lead free (Top
Mark: C5C)
2-pin header
3.6µH, 1.8A power inductor
Sumida CMD6D11BHPNP-3R6MC
0Ω resistor (0603)
200kΩ ±1% resistors (0603)
Recommended Equipment
DESCRIPTION
Quick Start
Procedure
81-3-3343-3411
888-522-5372
619-661-6322
847-545-6700
847-803-6100
949-455-2000
631-35-1110
770-36-1300
PHONE
3) Connect the positive terminal of the power supply to
4) Turn on the power supply and verify that the step-
5) Verify that the gate-on supply (GON) is approxi-
6) Verify that the gate-off supply (GOFF) is approxi-
7) Verify that the output of the high-speed op amp
8) Verify that the outputs of the high-voltage level-shift-
For instructions on selecting the step-up switching regu-
lator feedback and op amp divider resistors for other out-
put voltages, see the Output Voltage Selection section.
DESIGNATION QTY
R16, R17, R20
A1–A8, Y1–Y8
SW1, SW2
the VIN pad. Connect the negative terminal of the
power supply to the GND pad.
up switching regulator output (VMAIN) is 8.5V.
mately 23V.
mately -7.5V.
(VCOM) is 4.25V.
ing buffers are approximately 23V (= GON).
R18, R19
R7–R15
R3
R4
U1
—
Component List (continued)
1
1
9
0
0
2
1
0
1
Component Suppliers
www.centralsemi.com
www.fairchildsemi.com
www.murata.com
www.niec.co.jp
www.sanyodevice.com
www.sumida.com
www.component.tdk.com
www.toshiba.com/taec
34kΩ ±1% resistor (0603)
100kΩ ±1% resistor (0603)
100kΩ ±5% resistors (0603)
Not installed, resistors—shorted by
PC trace (0603)
Not installed, resistors—shorted by
PC trace (0402)
8-position, low-profile DIP switches
MAX17010TEL+ (40-pin TQFN,
5mm x 5mm)
Not installed, test points
PCB: MAX17010 Evaluation Kit+
DESCRIPTION
WEBSITE