HSM933-40.0000 Connor-Winfield, HSM933-40.0000 Datasheet - Page 2

• Manufacturer Part Number: HSM933-40.0000
• Description: OSC HCMOS 3.3V 40.0000MHZ SMD
• Manufacturer: Connor-Winfield
• Series: HSM9r
• Type: Standardr

Specifications of HSM933-40.0000

• Supply Voltage: 3.3V
• Frequency: 40MHz
• Frequency Stability: ±100ppm
• Operating Temperature: -10°C ~ 70°C
• Current - Supply (max): 20mA
• Mounting Type: Surface Mount
• Size / Dimension: 0.295" L x 0.197" W (7.50mm x 5.00mm)
• Height: 0.055" (1.40mm)
• Package / Case: SMD 7.50mm x 5.00mm
• Supply Current: 20mA
• Other names: Q841148

Tape and Reel Dimensions
Package
Temperature Cycle
Hermetical
Solvent Resistance
General Conditions 260°C max x 10 sec max x 2 times max or
Typical Operation Data
Free Drop
Vibration
Thermal Shock
Solderability
After performing the above procedures, a newly soldered coverage shall be greater than 90%
After performing the above procedures, a newly soldered coverage shall be greater than 90%
After performing the above procedures, a newly soldered coverage shall be greater than 90%
After performing the above procedures, a newly soldered coverage shall be greater than 90%
After performing the above procedures, a newly soldered coverage shall be greater than 90%
Dimensional Tolerance: ±.02” (.508mm)
Specifications subject to change without notice. All dimensions in inches. © Copyright 1998 The Connor-Winfield Corporation
Hermetically sealed ceramic package and metal cover
at 215°C, then down to room temperature per 1 to 5°C / sec
No bubbles appear in Flourinert (FC-43) at 125°C ±5°C for 5 minutes
The specimen shall meet electrical characteristics after tested 3 times,
1) Flux: MIL-F-14256 (WW Rosin=25%, Isopropyl Alcohol = 75%)
2) Solder: QQ-S-571 (Sn = 63%, Pb = 37%)
3) Solder bath temperature: 235°C ±5°C
4) Depth of immersion: Up to electrical terminal
5) Immersing time: Within 2 sec ±0.5 sec into solder bath
Free Drop testing on the hard wooden board from a height of 75 cm.
tested 5 cycles of -55°C / 30 minutes and +125°C / 30 minutes
The specimen shall meet electrical characteristics after tested
max x 10 sec max x 2 times, or 230°C max x 180 sec max,
The specimen shall meet electrical characteristics after
by the following conditions: 10-55Hz 1.5mm Amplitude,
Isopropyl Alcohol or Trichloroethylene
Environmental Characteristics
Marking will withstand immersion in
the specimen shall meet electrical characteristics
230°C max x 180 sec max x 1 time
20 to 100 sec up to 215°C, 50 sec
Mechanical Characteristics
Package Characteristics
±.005” (.127mm)
55-2000 Hz 20 G's, 2 hours for each plane
After applied Thermal Shock of 260°C
(Vapor phase reflow)
(EIAJ-RCX-0102.101 Condition 1a)
Soldering
Pin Connections
1: Tri-State E/D
2: Ground
3: Output
4: VDD
Dimensional Tolerance: ±.02” (.
±.005” (.1
Marking Information
Part
Number
HSM913 HSM913XX
HSM923 HSM923XX
HSM933 HSM933XX
HSM943 HSM943XX
Ordering Information
CLOCK
SERIES
HSM943 - 125.0M
Suggested Pad Layout
Marking
Variations
HM913XX
HM923XX
HM933XX
HM943XX
XX = Date Code
Output Waveform
Test Circuit
Bulletin
Page
Revision
Date
2111 Comprehensive Drive
Aurora, Illinois 60505
Phone: [phone]
www.conwin.com
Fax: [phone]
27 Nov 2007
CENTER
FREQUENCY
Sm007
2 of 2
29