84C1D-F40-J15 Bourns Inc., 84C1D-F40-J15 Datasheet

Panel Mount Potentiometers 5/8 10K 5% Square 10 Turn

84C1D-F40-J15

Manufacturer Part Number
84C1D-F40-J15
Description
Panel Mount Potentiometers 5/8 10K 5% Square 10 Turn
Manufacturer
Bourns Inc.
Type
Potentiometerr
Datasheet

Specifications of 84C1D-F40-J15

Resistance
10kohm
Power Rating
1W
Tolerance (+ Or -)
5%
Number Of Turns
10Turn
Technology
Wirewound
Mounting Style
Panel
Termination Style
Solder Lug
Operating Temp Range
1C to 125C
Failure Rate
Not Required
Shaft Diameter (mm)
3.18mm
Product Diameter (mm)
Not Requiredmm
Product Height (mm)
17.4mm
Product Depth (mm)
15.88mm
Temperature Coefficient
±50
Tolerance
5 %
Taper
Linear
Element Type
Wire Wound
Shaft Type
Flatted / D
Shaft Length
1 1/4 in
Shaft Diameter
1/8 in
Operating Temperature Range
+ 1 C to + 125 C
Product
Panel Mount Potentiometers
Lead Free Status / RoHS Status
Not Compliant
Standard Resistance Range ........................................................................ 200 to 100 K ohms............................................... 1 K to 100 K ohms
Total Resistance Tolerance .......................................................................... ±5 % .................................................................... ±10 %
Independent Linearity .................................................................................. ±0.25 % ............................................................... ±0.25 %
Absolute Minimum Resistance (J Taper) ..................................................... 1.0 ohm or 0.1 % (whichever is greater) .............. –
Effective Electrical Angle ............................................................................. 3600 ° +10 °, -0 ° ................................................. 3600 ° +10 °, -0 °
Dielectric Withstanding Voltage (MIL-STD-202, Method 301)
Insulation Resistance (500 VDC) ................................................................. 1,000 megohms minimum ................................... 1,000 megohms minimum
Power Rating (Voltage Limited By Power Dissipation or 350 VAC, Whichever Is Less)
Theoretical Resolution ................................................................................. See table .............................................................. Essentially infi nite
End Voltage (K Taper) .................................................................................. – ........................................................................... 0.2 % of applied voltage
Noise (J Taper) ............................................................................................. 100 ohms ENR maximum .................................... –
Output Smoothness (K Taper) ..................................................................... – ........................................................................... 0.15 % maximum
Operating Temperature Range .................................................................... +1 °C to +125 °C ................................................. +1 °C to +125 °C
Storage Temperature Range ....................................................................... -55 °C to +125 °C ................................................ -55 °C to +125 °C
Temperature Coeffi cient Over Storage Temperature Range ....................... ±50 ppm/°C ......................................................... ±100 ppm/°C
Vibration ...................................................................................................... 15 G ..................................................................... 15 G
Shock .......................................................................................................... 50 G ..................................................................... 50 G
Load Life ...................................................................................................... 1,000 hours .......................................................... 1,000 hours
Rotational Life (No Load) ............................................................................. 1,000,000 shaft revolutions .................................. 4,000,000 shaft revolutions
Moisture Resistance (MIL-STD-202, Method 103, Condition B)
IP Rating ...................................................................................................... IP 40 ..................................................................... IP 40
Stop Strength ......................................................................................................................................................................33.90 N-cm (48.0 oz.-in.) minimum
Mechanical Angle ........................................................................................................................................................................................... 3600 ° +15 °, -0 °
Torque
Shaft Runout ...................................................................................................................................................................................... 0.15 mm (0.006 in.) T.I.R.
Shaft End Play .................................................................................................................................................................................... 0.36 mm (0.014 in.) T.I.R.
Shaft Radial Play ................................................................................................................................................................................ 0.13 mm (0.005 in.) T.I.R.
Weight (Single Section)..................................................................................................................................................................................... 21 gm (0.75 oz.)
Terminals ....................................................................................................................................................................... Printed circuit terminals or solder lugs
Marking ..........................................................................Manufacturer’s trademark, wiring diagram, date code and resistance, manufacturer’s part number
Ganging (Multiple Section Potentiometers) ...................................................................................................................................................... 2 cup maximum
Hardware ............................................One lockwasher and one mounting nut is shipped with each potentiometer, except where noted in the part number.
NOTE: Model 83/84 performance specifi cations do not apply to units subjected to printed circuit board cleaning procedures.
1 At room ambient: +25 °C nominal and 50 % relative humidity nominal, except as noted.
Initial Electrical Characteristics
Environmental Characteristics
Mechanical Characteristics
Sea Level ............................................................................................... 1,000 VAC minimum ............................................ 1,000 VAC minimum
+70 °C .................................................................................................. 1 watt ................................................................... 1 watts
+125 °C ................................................................................................. 0 watt ................................................................... 0 watt
Total Resistance Shift ............................................................................ ±2 % .................................................................... ±2 %
Voltage Ratio Shift ................................................................................. ±0.2 % ................................................................. ±0.2 %
Wiper Bounce........................................................................................ 0.1 millisecond maximum .................................... 0.1 millisecond maximum
Total Resistance Shift ............................................................................ ±2 % .................................................................... ±2 %
Voltage Ratio Shift ................................................................................. ±0.2 % ................................................................. ±0.2 %
Wiper Bounce........................................................................................ 0.1 millisecond maximum .................................... 0.1 millisecond maximum
Total Resistance Shift ............................................................................ ±2 % maximum ................................................... ±5 % maximum
Total Resistance Shift ............................................................................ ±5 % maximum .................................................. ±5 % maximum
Total Resistance Shift ............................................................................ ±2 % maximum ................................................... ±5 % maximum
Insulation Resistance (500 VDC) ........................................................... 100 megohms minimum ...................................... 100 megohms minimum
Starting ............................................................................................................................................. Running torque plus 0.7 N-cm (1.0 oz.-in.) maximum
Running (1 or 2 Section) ........................................................................................................................................... 0.18 to 1.41 N-cm (0.25 to 2.0 oz.-in.)
Mounting (Torque on Bushing) .................................................................................................................................. 1.7-2.0 N-m (15-18 lb.-in.) maximum
(Each Additional Section) ........................................................................................................................................................................... 18 gm (0.65 oz.)
Soldering Condition ...................................................................Recommended hand soldering using Sn95/Ag5 no clean solder, 0.025 ” wire diameter.
1
1
1
Maximum temperature 399 °C (750 °F) for 3 seconds. No wash process to be used with no clean fl ux
Features
83/84 - 5/8 ” Square 10-Turn
Compatible with other members of the Model 80 Series
The only 10-turn precision potentiometer in a modular panel control package
Up to 2 sections available
Wirewound Element (J Taper)
Customers should verify actual device performance in their specifi c applications.
*RoHS Directive 2002/95/EC Jan 27 2003 including Annex
Specifi cations are subject to change without notice.
Hybriton
®
Element (K Taper)

Related parts for 84C1D-F40-J15

84C1D-F40-J15 Summary of contents

Page 1

Initial Electrical Characteristics Standard Resistance Range ........................................................................ 200 to 100 K ohms............................................... 100 K ohms Total Resistance Tolerance .......................................................................... ±5 % .................................................................... ±10 % Independent Linearity .................................................................................. ±0.25 % ............................................................... ±0.25 % Absolute Minimum Resistance (J ...

Page 2

Square 10-Turn Wirewound Resolution Table Resistance Resolution (Ohms) (Nom.) (%) 200 .048 500 .037 1 K .032 2 K .031 5 K .023 10 K .020 20 K .015 50 K .012 100 K .010 Specifi ...

Page 3

Square 10-Turn Product Dimensions PC Pin Model 83 19.05 ± .51 (.75 ± .02) .79 ± .41 (.031 ± .016) 6.10 ± .51 (FMS (.24 ± .02) 6.35 ± 1.02 .30 (.25 ...

Page 4

Square 10-Turn How To Order ANTI-ROTATION LUG A Single .305 R, 90 °CW B Double .305 R, 90 ° & 270 °CW C Single .305 R, 270 ° Lug ...

Related keywords