EVB-EMC1063 SMSC, EVB-EMC1063 Datasheet
EVB-EMC1063
Specifications of EVB-EMC1063
Related parts for EVB-EMC1063
EVB-EMC1063 Summary of contents
Page 1
... EVB-EMC1043/1053/1063 User Manual The information contained herein is proprietary to SMSC, and shall be used solely in accordance with the agreement pur- suant to which it is provided. Although the information is believed to be accurate, no responsibility is assumed for inaccu- racies. SMSC reserves the right to make changes to this document and to specifications and product descriptions at any time without notice ...
Page 2
... Ideality Factor Configuration is available to accomodate remote diodes with a wide range of ideality factors. This is especially important for microprocessors, FPGAs, and graphics chips. The EVB-EMC1043, EVB-EMC1053 and EVB-EMC1063 are USB-based platforms for evaluating the EMC1043/1053/1063 ICs. A block diagram of the EVB is shown in Revision 1.1 (12-14-06) ...
Page 3
... Mini-B SMBus Bridge USB Activity LED7 Bridge Activity LED6 Vdd LED8 Figure 1.1 EMC1043/1053/1063 EVB Block Diagram 1.1 Related Documents The CD included with the evaluation board contains the following documents: Evaluation Board Checklist n Bill Of Materials n Schematic n Jumper Settings and Connector List ...
Page 4
... Getting Started 2.1 System Requirements To use the EVB you will need running Windows 2000 Display resolution 800x600 (or larger to view several windows simultaneously available USB port n 2.1.1 Feature Summary Windows Register Manager application allows viewing and changing register values as well as n graphing temperature history ...
Page 5
... Connect the supplied USB cable to an available USB port on the PC. Plug the “mini-B” end of the USB cable into EVB connector P6. The +3.3V and Bridge ACT LEDs should illuminate. After the EVB is connected to the PC the “Find New Hardware” wizard will pop up for USB driver installation. Follow the instructions in the readme.txt file to complete the installation process. ...
Page 6
... Figure 2.2 Register Manager Help Screen Revision 1.1 (12-14-06) EVB-EMC1043/1053/1063 User Manual SMSC EMC1043/1053/1063 6 ...
Page 7
... EMC1043/1053/1063 and other EVB circuits. 3.6 Direct SMBus Connect Option It is also possible to connect an external SMBus master to the EMC1043/1053/1063 EVB. A few modifications to the circuit are required: Cut 3 traces connecting JP4 pins 3-4, 5-6 and 7-8 on the bottom side of the PCB. This will n disconnect the USB bridge from the SMBus ...
Page 8
... Bridge Activity, when ON indicates the Bridge is functioning n 3.9 Other Sensor Features Other features such as Ideality Factor Configuration, Conversion Rate, Dynamic Averaging, Hottest of 2 Zones and Standby Mode can be controlled with EMC1043/1053/1063 registers. See the datasheet register description for details. Revision 1.1 (12-14-06) EVB-EMC1043/1053/1063 User Manual SMSC EMC1043/1053/1063 8 ...
Page 9
... EVB-EMC1043/1053/1063 User Manual 4 Demo Description 4.1 Register Manager Overview The Register Manager application (RegMan) initially displays the main Help screen, where detailed description of the application’s features may be found. The Help screens can be displayed at any time by selecting Help from the menubar or pressing the ? button on the toolbar. RegMan enables the user to display temperature readings, set temperature limits and read/write configuration register values ...
Page 10
... Ideality Factor Correction The Ideality Factor can be adjusted in Ideality Factor Registers 0x27 and 0x28. These registers will normally hold the default value which is correct for the diodes installed on the EVB. Increasing or decreasing the value will cause a corresponding change in the temperature reading. ...