AD623ARM-REEL7 Analog Devices Inc, AD623ARM-REEL7 Datasheet - Page 20
![no-image](/images/manufacturer_photos/0/0/57/analog_devices_inc_sml.jpg)
AD623ARM-REEL7
Manufacturer Part Number
AD623ARM-REEL7
Description
IC,Instrumentation Amplifier,SINGLE,SSOP,8PIN,PLASTIC
Manufacturer
Analog Devices Inc
Datasheet
1.AD623-EVAL.pdf
(24 pages)
Specifications of AD623ARM-REEL7
Rohs Status
RoHS non-compliant
Amplifier Type
Instrumentation
Number Of Circuits
1
Output Type
Rail-to-Rail
Slew Rate
0.3 V/µs
-3db Bandwidth
800kHz
Current - Input Bias
17nA
Voltage - Input Offset
200µV
Current - Supply
375µA
Voltage - Supply, Single/dual (±)
2.7 V ~ 12 V, ± 2.5 V ~ 6 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
8-MSOP, Micro8™, 8-uMAX, 8-uSOP,
Current - Output / Channel
-
Gain Bandwidth Product
-
Lead Free Status / RoHS Status
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AD623ARM-REEL7
Manufacturer:
AD
Quantity:
5 510
Company:
Part Number:
AD623ARM-REEL7
Manufacturer:
AD
Quantity:
5 510
AD623
Amplifying Signals with Low Common-Mode Voltage
Because the common-mode input range of the AD623 extends
0.1 V below ground, it is possible to measure small differential
signals which have low, or no, common-mode component.
Figure 54 shows a thermocouple application where one side
of the J-type thermocouple is grounded.
Over a temperature range of −200°C to +200°C, the J-type thermo-
couple delivers a voltage ranging from −7.890 mV to +10.777 mV.
A programmed gain on the AD623 of 100 (R
voltage on the REF pin of 2 V, results in the output voltage ranging
from 1.110 V to 3.077 V relative to ground.
INPUT DIFFERENTIAL AND COMMON-MODE RANGE
vs. SUPPLY AND GAIN
Figure 55 shows a simplified block diagram of the AD623. The
voltages at the outputs of Amplifier A1 and Amplifier A2 are
given by
V
The voltages on these internal nodes are critical in determining
whether the output voltage will be clipped. The V
voltages can swing from approximately 10 mV above the negative
supply (V− or ground) to within approximately 100 mV of the
positive rail before clipping occurs. Based on this and from
CM
V
V
Figure 54. Amplifying Bipolar Signals with Low Common-Mode Voltage
DIFF
DIFF
V
V
2
2
THERMOCOUPLE
A2
A1
NONINVERTING
–
+
–
+
INVERTING
= V
= V
= V
= V
2
3
CM
CM
CM
CM
J-TYPE
NEGATIVE SUPPLY
POSITIVE SUPPLY
+ V
+ V
+ 0.6 V + V
+ 0.6 V − V
Figure 55. Simplified Block Diagram
DIFF
DIFF
GAIN
R
7
4
7
4
G
/2 + 0.6 V + V
/2 + 0.6 V + V
1
8
DIFF
DIFF
1.02kΩ
× Gain /2
× Gain /2
50kΩ
50kΩ
A1
A2
R
R
R
F
F
G
DIFF
DIFF
AD623
50kΩ
50kΩ
5V
× R
× R
0.1µF
G
F
F
/ R
/ R
= 1.02 kΩ) and a
REF
50kΩ
50kΩ
G
G
A3
A1
and V
OUTPUT
2V
A2
OUTPUT
REF
Rev. D | Page 20 of 24
6
5
the previous equations, the maximum and minimum input
common-mode voltages are given by the following equations:
These equations can be rearranged to give the maximum
possible differential voltage (positive or negative) for a
particular common-mode voltage, gain, and power supply.
Because the signals on A1 and A2 can clip on either rail, the
maximum differential voltage are the lesser of the two equations.
However, the range on the differential input voltage range is
also constrained by the output swing. Therefore, the range of
V
For a bipolar input voltage with a common-mode voltage that is
roughly half way between the rails, V
the previous equations yield because the REF pin is at midsupply.
Note that the available output swing is given for different supply
conditions in the Specifications section.
The equations can be rearranged to give the maximum gain for
a fixed set of input conditions. Again, the maximum gain will be
the lesser of the two equations.
Again, it is recommended that the resulting gain times the input
range is less than the available output swing. If this is not the
case, the maximum gain is given by
Also for bipolar inputs (that is, input range = 2 V
maximum gain is half the value yielded by the previous equations
because the REF pin must be at midsupply.
The maximum gain and resulting output swing for different
input conditions is given in Table 8. Output voltages are
referenced to the voltage on the REF pin.
For the purposes of computation, it is necessary to break down the
input voltage into its differential and common-mode component.
Therefore, when one of the inputs is grounded or at a fixed
voltage, the common-mode voltage changes as the differential
voltage changes. Take the case of the thermocouple amplifier
in Figure 54. The inverting input on the AD623 is grounded;
therefore, when the input voltage is −10 mV, the voltage on the
noninverting input is −10 mV. For the purpose of the signal swing
calculations, this input voltage should be composed of a common-
mode voltage of −5 mV (that is, (+IN + −IN)/2) and a differential
input voltage of −10 mV (that is, +IN − −IN).
DIFF
V
V
| V
| V
Input Range ≤ Available Output Swing/Gain
Gain
Gain
Gain
may have to be lower according the following equation.
CMMAX
CMMIN
DIFFMAX
DIFFMAX
MAX
MAX
MAX
= V − − 0.590 V + V
= V + − 0.7 V − V
| = 2 ( V + − 0.7 V − V
| = 2 ( V
= 2 ( V + − 0.7 V − V
= 2 ( V
= Available Output Swing/Input Range
CM
CM
− V− +0.590 V )/ V
− V − +0.590 V/ Gain
DIFF
DIFF
× Gain /2
CM
CM
× Gain /2
)/ V
/ Gain
DIFFMAX
DIFF
DIFF
is half the value that
DIFF
), the