AD7884BPZ-REEL Analog Devices Inc, AD7884BPZ-REEL Datasheet - Page 8

• Manufacturer Part Number: AD7884BPZ-REEL
• Description: 16-BIT PARAL.SAMPL ADC
• Manufacturer: Analog Devices Inc

Specifications of AD7884BPZ-REEL

• Number Of Bits: 16
• Sampling Rate (per Second): 166k
• Data Interface: Parallel
• Number Of Converters: 2
• Power Dissipation (max): 325mW
• Voltage Supply Source: Dual ±
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 44-PLCC
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

AD7884/AD7885
TERMINOLOGY
Integral Nonlinearity
This is the maximum deviation from a straight line passing
through the endpoints of the ADC transfer function.
Differential Nonlinearity
This is the difference between the measured and the ideal 1 LSB
change between any two adjacent codes in the ADC.
Bipolar Zero Error
This is the deviation of the midscale transition (all 0s to all 1s)
from the ideal (AGND).
Positive Gain Error
This is the deviation of the last code transition (01 . . . 110 to
01 . . . 111) from the ideal (+V
error has been adjusted out.
Negative Gain Error
This is the deviation of the first code transition (10 . . . 000 to
10 . . . 001) from the ideal (–V
error has been adjusted out.
Signal-to-(Noise + Distortion) Ratio
This is the measured ratio of signal-to-(noise + distortion) at the
output of the A/D converter. The signal is the rms amplitude of
the fundamental. Noise is the rms sum of all nonfundamental
signals up to half the sampling frequency (f
The ratio is dependent upon the number of quantization levels
in the digitization process; the more levels, the smaller the quan-
tization noise. The theoretical signal-to-(noise + distortion) ratio
for an ideal N-bit converter with a sine wave input is given by
Thus for an ideal 16-bit converter, this is 98 dB.
Total Harmonic Distortion
Total harmonic distortion (THD) is the ratio of the rms sum of
harmonics to the fundamental. For the AD7884/AD7885, it is
defined as
where V
V
sixth harmonics.
Peak Harmonic or Spurious Noise
Peak harmonic or spurious noise is defined as the ratio of the rms
value of the next largest component in the ADC output spectrum
(up to f
Normally, the value of this specification is determined by the larg-
est harmonic in the spectrum, but for parts where the harmonics
are buried in the noise floor, it will be a noise peak.
Intermodulation Distortion
With inputs consisting of sine waves at two frequencies, fa and
fb, any active device with nonlinearities will create distortion
products at sum and difference frequencies of mfa ± nfb where
m, n = 0, 1, 2, 3, and so on. Intermodulation terms are those for
which neither m nor n are equal to zero. For example, the second
order terms include (fa + fb) and (fa – fb), while the third order
terms include (2fa + fb), (2fa – fb), (fa + 2fb), and (fa – 2fb).
4
, V
5
Signal to Noise
, and V
S
1
/2 and excluding dc) to the rms value of the fundamental.
THD dB
is the rms amplitude of the fundamental and V
− −
6
(
are the rms amplitudes of the second through the
(
)
=
20
+
log
Distortion
V
REF+
REF+
2
2
+
S + 1 LSB) after bipolar zero
S – 1 LSB) after bipolar zero
V
)
3
=
2
(
+
6 02
V
V
.
1
4
S
2
/2), excluding dc.
+
N
V
5
+
2
1 76
+
.
V
6
2
)
dB
2
, V
3
,
–8–
The AD7884/AD7885 is tested using the CCIFF standard where
two input frequencies near the top end of the input bandwidth are
used. In this case, the second and third order terms are of different
significance. The second order terms are usually distanced in
frequency from the original sine waves while the third order terms
are usually at a frequency close to the input frequencies. As a
result, the second and third order terms are specified separately.
The calculation of the intermodulation distortion is as per the THD
specification, where it is the ratio of the rms sum of the individual
distortion products to the rms amplitude of the fundamental
expressed in dB.
Power Supply Rejection Ratio
This is the ratio of the change in positive gain error to the change
in V
OPERATIONAL DIAGRAM
An operational diagram for the AD7884/AD7885 is shown in
Figure 6. It is set up for an analog input range of ± 5 V. If a ± 3 V
input range is required, A1 should drive ± 3V
with ± 5V
The chosen input buffer amplifier (A1) should have low noise and
distortion and fast settling time for high bandwidth applications.
The AD711, AD845, and AD817 are suitable op amps.
A2 is the force, sense amplifier for AGND. The AGNDS pin
should be at zero potential. Therefore, the amplifier must have a
low input offset voltage and good noise performance. It must
also have the ability to deal with fast current transients on the
AGNDS pin. The AD817 has the required performance and is
the recommended amplifier.
If AGNDS and AGNDF are simply tied together to star
ground instead of buffering, the SNR and THD are not signifi-
cantly degraded. However, dc specifications like INL, bipolar
zero, and gain error will be degraded.
NOTE: POWER SUPPLY DECOUPLING NOT SHOWN
V
8
DD
DD
AD780
= +5V
Figure 6. AD7884/AD7885 Operational Diagram
2
or V
4
IN
6
V
S, ± 5V
IN
SS
10 F
, in dB. It is a dc measurement.
IN
A1
A2
A3
A4
AD845, AD817,
OR EQUIVALENT
AD845, AD817,
OR EQUIVALENT
F being tied to system AGND.
AD711, AD845,
OR AD817
AD817
AGNDS
AGNDF
V
V
V
V
AV
REF+
REF+
INV
REF–
5V
5V
3V
3V
DD
IN
IN
IN
IN
S
F
S
F
S
F
GND
V
+5V
DD
AD7884/
AD7885
AV
DGND
IN
SS
S and ± 3V
–5V
V
SS
DATA
OUTPUTS
CONTROL
INPUTS
REV. E
IN
F