AD8290ACPZ-RL Analog Devices Inc, AD8290ACPZ-RL Datasheet - Page 17
![IC,Sense Amplifier,SINGLE,CMOS,LLCC,16PIN,PLASTIC](/photos/6/50/65061/505-16-lfcsp_sml.jpg)
AD8290ACPZ-RL
Manufacturer Part Number
AD8290ACPZ-RL
Description
IC,Sense Amplifier,SINGLE,CMOS,LLCC,16PIN,PLASTIC
Manufacturer
Analog Devices Inc
Datasheet
1.AD8290ACPZ-RL.pdf
(20 pages)
Specifications of AD8290ACPZ-RL
Amplifier Type
Current Sense
Number Of Circuits
1
-3db Bandwidth
250Hz
Current - Input Bias
100pA
Current - Supply
1.2mA
Voltage - Supply, Single/dual (±)
2.6 V ~ 5.5 V, ±1.3 V ~ 2.75 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
16-LFCSP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Output Type
-
Current - Output / Channel
-
Slew Rate
-
Gain Bandwidth Product
-
Voltage - Input Offset
-
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
MAXIMIZING PERFORMANCE THROUGH PROPER
LAYOUT
To achieve the maximum performance of the AD8290, care
should be taken in the circuit board layout. The PCB surface
must remain clean and free of moisture to avoid leakage currents
between adjacent traces. Surface coating of the circuit board
reduces surface moisture and provides a humidity barrier,
reducing parasitic resistance on the board.
R
The paddle on the bottom of the package should not be connected
to any potential and should be floating.
For high impedance sources, the PCB traces from the AD8290
inputs should be kept to a minimum to reduce input bias
current errors.
POWER SUPPLY BYPASSING
The AD8290 uses internally generated clock signals to perform
autocorrection. As a result, proper bypassing is necessary to
achieve optimum performance. Inadequate or improper bypassing
of the supply lines can lead to excessive noise and offset voltage.
A 0.1 μF surface-mount capacitor should be connected between
Pin 2 (VCC) and Pin 10 (GND) when operating with a single
supply and should be located as close as possible to those two pins.
SET
should be placed close to RSET (Pin 11) and GND (Pin 10).
C
NC = NO CONNECT
NOTES
LAYOUT CONSIDERATIONS:
1. KEEP C1 CLOSE TO PIN 2 AND PIN 10.
2. KEEP C3 CLOSE TO PIN 2.
3. KEEP C5 CLOSE TO PIN 10.
4. KEEP R
BRIDGE
SET
692Ω TO 3kΩ
CLOSE TO PIN 11.
–1.8V
R
SET
Figure 46. Typical Dual-Supply Connections
–1.8V
13
14
15
IOUT
VINN
VINP
RSET
Rev. B | Page 17 of 20
11
NC
1
NC
7
CF1
6
AD8290
NC
C
6.8nF
8
FILTER
–1.8V
DUAL-SUPPLY OPERATION
The AD8290 can be configured to operate in dual-supply mode.
An example of such a circuit is shown in Figure 46, where the
AD8290 is powered by ±1.8 V supplies. When operating with
dual supplies, pins that are normally referenced to ground in the
single-supply mode, now need to be referenced to the negative
supply. These pins include the following: Pin 1, Pin 7, Pin 8, Pin 9,
Pin 10, Pin 12, and Pin 16. External components, such as R
sensing bridge, and the antialiasing filter capacitor at the output,
should also be referenced to the negative supply. Additionally,
two bypass capacitors should be added beyond what is necessary
for single-supply operation: one between the negative supply
and ground, and the other between the positive and negative
supplies.
When operating in dual-supply mode, the specifications change
and become relative to the negative supply. The input voltage
range minimum shifts from 0.2 V to 0.2 V above the negative
supply (in this example: −1.6 V), the output voltage range shifts
from a minimum of 0.075 V to 0.075 V above the negative supply
(in this example: −1.725 V), and the excitation current pin
voltage minimum shifts from 0 V to −1.8 V in this example.
The maximum specifications of these three parameters are
specified relative to V
For other specifications, both the minimum and maximum
specifications change. The output offset shifts from a minimum
of +865 mV and maximum of +935 mV to a minimum of
−935 mV and a maximum of −865 mV in the example. In
addition, the logic levels for the ENBL operation should be
adjusted accordingly.
NC
CF2
9
5
NC
12
ENBL
VOUT
3
GND
VCC
NC
16
10
4
2
CC
C1
0.1µF
C2
68nF
in Table 1 and do not change.
V
C3
0.1µF
C5
0.1µF
OUT
1.8V
–1.8V
AD8290
SET
, the