AD9204-65EBZ Analog Devices Inc, AD9204-65EBZ Datasheet - Page 31
![no-image](/images/manufacturer_photos/0/0/57/analog_devices_inc_sml.jpg)
AD9204-65EBZ
Manufacturer Part Number
AD9204-65EBZ
Description
10 Bit 65 Msps Dual Low Power ADC
Manufacturer
Analog Devices Inc
Datasheet
1.AD9204BCPZ-20.pdf
(36 pages)
Specifications of AD9204-65EBZ
Number Of Adc's
2
Number Of Bits
10
Sampling Rate (per Second)
65M
Data Interface
Serial, SPI™
Inputs Per Adc
1 Differential
Input Range
1 ~ 2 Vpp
Power (typ) @ Conditions
*
Voltage Supply Source
Single Supply
Operating Temperature
-40°C ~ 85°C
Utilized Ic / Part
AD9204
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
MEMORY MAP
READING THE MEMORY MAP REGISTER TABLE
Each row in the memory map register table (see Table 17) has
eight bit locations. The memory map is roughly divided into
four sections: the chip configuration registers (Address 0x00
to Address 0x02); the device index and transfer registers
(Address 0x05 and Address 0xFF); the program registers
(Address 0x08 to Address 0x2E); and the digital feature control
registers (Address 0x100 and Address 0x101).
Table 17 documents the default hexadecimal value for each
hexadecimal address shown. The column with the heading Bit 7
(MSB) is the start of the default hexadecimal value given. For
example, Address 0x18, the VREF register, has a hexadecimal
default value of 0xE0. This means that Bits[7:5] = 1, and the
remaining Bits[4:0] = 0. This setting is the default reference
selection setting. The default value uses a 2.0 V p-p reference.
For more information on this function and others, see the AN-877
Application Note, Interfacing to High Speed ADCs via SPI. This
document details the functions controlled by Register 0x00 to
register 0xFF. The remaining registers, Register 0x100 and
Register 0x101, are documented in the Memory Map Register
Descriptions section following Table 17.
OPEN LOCATIONS
All address and bit locations that are not included in the SPI
map are not currently supported for this device. Unused bits of
a valid address location should be written with 0s. Writing to these
locations is required only when part of an address location is
open (for example, Address 0x18). If the entire address location
is open, it is omitted from the SPI map (for example, Address 0x13)
and should not be written.
Rev. 0 | Page 31 of 36
DEFAULT VALUES
After the AD9204 is reset, critical registers are loaded with
default values. The default values for the registers are given
in the memory map register table (see Table 17).
Logic Levels
An explanation of logic level terminology follows:
•
•
Transfer Register Map
Address 0x08 to Address 0x18 are shadowed. Writes to these
addresses do not affect part operation until a transfer command
is issued by writing 0x01 to Address 0xFF, setting the transfer bit.
This allows these registers to be updated internally and simulta-
neously when the transfer bit is set. The internal update takes
place when the transfer bit is set, and then the bit autoclears.
Channel-Specific Registers
Some channel setup functions can be programmed differently
for each channel. In these cases, channel address locations are
internally duplicated for each channel. These registers and bits
are designated in the memory map register table as local. These
local registers and bits can be accessed by setting the appropriate
Channel A (Bit 0) or Channel B (Bit 1) bits in Register 0x05.
If both bits are set, the subsequent write affects the registers of
both channels. In a read cycle, set only Channel A or Channel B
to read one of the two registers. If both bits are set during an
SPI read cycle, the part returns the value for Channel A.
Registers and bits designated as global in the memory map
register table affect the entire part or the channel features for
which independent settings are not allowed between channels.
The settings in Register 0x05 do not affect the global registers
and bits.
“Bit is set” is synonymous with “bit is set to Logic 1” or
“writing Logic 1 for the bit. ”
“Clear a bit” is synonymous with “bit is set to Logic 0” or
“writing Logic 0 for the bit. ”
AD9204