AD9248BCP-65EB Analog Devices Inc, AD9248BCP-65EB Datasheet - Page 19
![no-image](/images/manufacturer_photos/0/0/57/analog_devices_inc_sml.jpg)
AD9248BCP-65EB
Manufacturer Part Number
AD9248BCP-65EB
Description
Ard 14BIT DUAL 3V CMOS 65 MSPS ADC
Manufacturer
Analog Devices Inc
Specifications of AD9248BCP-65EB
Number Of Adc's
2
Number Of Bits
14
Sampling Rate (per Second)
20M
Data Interface
Parallel
Inputs Per Adc
1 Differential
Input Range
2 Vpp
Power (typ) @ Conditions
640mW @ 65MSPS
Voltage Supply Source
Single
Operating Temperature
-40°C ~ 85°C
Utilized Ic / Part
AD9248BCP-65
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant, Contains lead / RoHS non-compliant
POWER DISSIPATION AND STANDBY MODE
The power dissipated by the AD9248 is proportional to its
sampling rates. The digital (DRVDD) power dissipation is
determined primarily by the strength of the digital drivers and
the load on each output bit. The digital drive current can be
calculated by
where N is the number of bits changing, and C
load on the digital pins that changed.
The analog circuitry is optimally biased so that each speed
grade provides excellent performance while affording reduced
power consumption. Each speed grade dissipates a baseline
power at low sample rates that increases with clock frequency.
Either channel of the AD9248 can be placed into standby mode
independently by asserting the PDWN_A or PDWN_B pins.
It is recommended that the input clock(s) and analog input(s)
remain static during either independent or total standby, which
results in a typical power consumption of 1 mW for the ADC.
Note that if DCS is enabled, it is mandatory to disable the clock
of an independently powered-down channel. Otherwise,
significant distortion results on the active channel. If the clock
inputs remain active while in total standby mode, typical power
dissipation of 12 mW results.
The minimum standby power is achieved when both channels
are placed into full power-down mode (PDWN_A = PDWN_B =
HI). Under this condition, the internal references are powered
down. When either or both of the channel paths are enabled
after a power-down, the wake-up time is directly related to the
recharging of the REFT and REFB decoupling capacitors and to
the duration of the power-down. Typically, it takes approximately
5 ms to restore full operation with fully discharged 0.1 μF and
10 μF decoupling capacitors on REFT and REFB.
I
DRVDD
A
B
= V
–1
–1
DRVDD
Figure 34. Multiplexed Data Format Using the Channel A Output and the Same Clock Tied to CLK_A, CLK_B, and MUX_SELECT
B
–8
× C
A
B
t
PD
0
0
LOAD
A
–7
× f
B
–7
CLOCK
A
B
1
1
A
–6
× N
B
–6
A
B
2
2
A
LOAD
–5
t
PD
B
is the average
–5
A
B
3
3
A
–4
Rev. B | Page 19 of 48
B
–4
A
B
4
4
A
–3
B
–3
A single channel can be powered down for moderate power
savings. The powered-down channel shuts down internal
circuits, but both the reference buffers and shared reference
remain powered on. Because the buffer and voltage reference
remain powered on, the wake-up time is reduced to several
clock cycles.
DIGITAL OUTPUTS
The AD9248 output drivers can be configured to interface with
2.5 V or 3.3 V logic families by matching DRVDD to the digital
supply of the interfaced logic. The output drivers are sized to
provide sufficient output current to drive a wide variety of logic
families. However, large drive currents tend to cause current
glitches on the supplies that may affect converter performance.
Applications requiring the ADC to drive large capacitive loads
or large fanouts may require external buffers or latches.
The data format can be selected for either offset binary or twos
complement. See the Data Format section for more information.
TIMING
The AD9248 provides latched data outputs with a pipeline delay
of seven clock cycles. Data outputs are available one propa-
gation delay (t
to Figure 2 for a detailed timing diagram.
The internal duty cycle stabilizer can be enabled on the AD9248
using the DCS pin. This provides a stable 50% duty cycle to
internal circuits.
The length of the output data lines and loads placed on them
should be minimized to reduce transients within the AD9248.
These transients can detract from the converter’s dynamic
performance. The lowest typical conversion rate of the AD9248
is 1 MSPS. At clock rates below 1 MSPS, dynamic performance
may degrade.
A
B
5
5
A
–2
B
–2
A
B
6
6
A
PD
–1
) after the rising edge of the clock signal. Refer
B
–1
A
B
7
7
A
0
B
0
A
B
8
8
A
1
ANALOG INPUT
ADC A
ANALOG INPUT
ADC B
CLK_A = CLK_B =
MUX_SELECT
D0_A TO
D11_A
AD9248