AD9854/PCBZ Analog Devices Inc, AD9854/PCBZ Datasheet - Page 39

• Manufacturer Part Number: AD9854/PCBZ
• Description: 300 MHZ QUADRATURE DDS SYN. Eval Board
• Manufacturer: Analog Devices Inc
• Series: AgileRF™r

Specifications of AD9854/PCBZ

• Main Purpose: Timing, Direct Digital Synthesis (DDS)
• Utilized Ic / Part: AD9854
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Secondary Attributes: -
• Embedded: -
• Primary Attributes: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

CR [8] is the internal update active bit. When this bit is set to
Logic 1, the I/O UD CLK pin is an output and the AD9854
generates the I/O UD CLK signal. When this bit is set to Logic 0,
external I/O UD CLK functionality is performed and the I/O
UD CLK pin is configured as an input.
CR [7] is reserved. Write to 0.
CR [6] is the inverse sinc filter bypass bit. When this bit is set,
the data from the DDS block goes directly to the output shaped
keying logic, and the clock to the inverse sinc filter is stopped.
Default is clear with the filter enabled.
CR [5] is the shaped keying enable bit. When this bit is set, the
output ramping function is enabled and is performed in
accordance with the CR [4] bit requirements.
SCLK
SDIO
SCLK
CS
SCLK
SCLK
SDIO
SDIO
SDIO
SDO
CS
CS
CS
I
7
I
7
I
7
I
7
I
6
I
6
I
6
I
6
INSTRUCTION CYCLE
I
5
INSTRUCTION CYCLE
INSTRUCTION CYCLE
INSTRUCTION CYCLE
I
I
5
I
5
5
I
4
I
I
4
I
4
4
Figure 61. 2-Wire Serial Port Read Timing Clock Stall High
Figure 59. 3-Wire Serial Port Read Timing Clock Stall Low
I
3
Figure 60. Serial Port Write Timing Clock Stall High
Figure 58. Serial Port Write Timing Clock Stall Low
I
I
I
3
3
3
I
2
I
I
I
2
2
2
I
1
I
I
1
I
1
Rev. E | Page 39 of 52
1
I
0
I
I
0
0
I
0
D
O7
CR [4] is the internal/external output shaped keying control bit.
When this bit is set to Logic 1, the output shaped keying factor is
internally generated and applied to both the I and Q paths.
When this bit is cleared (default), the output shaped keying
function is externally controlled by the user, and the ouput
shaped keying factor is the value of the I and Q output shaped
keying factor register. The two registers that are the output
shaped keying factors also default low such that the output is off
at power-up until the device is programmed by the user.
CR [3:2] are reserved. Write to 0.
CR [1] is the serial port MSB-/LSB-first bit. Default is low,
MSB first.
CR [0] is the serial port SDO active bit. Default is low, inactive.
D
D
7
7
D
O7
D
O6
D
6
D
D
O6
6
D
O5
D
DATA TRANSFER CYCLE
5
D
DATA TRANSFER CYCLE
DATA TRANSFER CYCLE
DATA TRANSFER CYCLE
O5
D
D
5
O4
D
4
DON'T CARE
D
O4
D
D
O3
4
D
3
D
O3
D
O2
D
D
D
3
2
O2
D
O1
D
D
D
1
O1
2
D
D
D
O0
0
O0
D
1
D
0
AD9854