ADA4851-2YRMZ-RL7 Analog Devices Inc, ADA4851-2YRMZ-RL7 Datasheet - Page 18
![no-image](/images/manufacturer_photos/0/0/57/analog_devices_inc_sml.jpg)
ADA4851-2YRMZ-RL7
Manufacturer Part Number
ADA4851-2YRMZ-RL7
Description
IC,Operational Amplifier,DUAL,BIPOLAR,TSSOP,8PIN,PLASTIC
Manufacturer
Analog Devices Inc
Datasheet
1.ADA4851-1YRJZ-R2.pdf
(24 pages)
Specifications of ADA4851-2YRMZ-RL7
Amplifier Type
Voltage Feedback
Number Of Circuits
2
Output Type
Rail-to-Rail
Slew Rate
375 V/µs
-3db Bandwidth
105MHz
Current - Input Bias
2.2µA
Voltage - Input Offset
600µV
Current - Supply
2.9mA
Current - Output / Channel
125mA
Voltage - Supply, Single/dual (±)
2.7 V ~ 12 V, ±1.35 V ~ 6 V
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
8-MSOP, Micro8™, 8-uMAX, 8-uSOP,
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Gain Bandwidth Product
-
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ADA4851-2YRMZ-RL7
Manufacturer:
ADI
Quantity:
3 000
Part Number:
ADA4851-2YRMZ-RL7
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Figure 42 illustrates how the rising edge settling time for the
amplifier is configured as a unity-gain follower, stretching out
as the top of a 1 V step input that approaches and exceeds the
specified input common-mode voltage limit.
For signals approaching the negative supply and inverting gain
and high positive gain configurations, the headroom limit is the
output stage. The ADA4851-1/ADA4851-2/ADA4851-4 amplifiers
use a common emitter output stage. This output stage maximizes
the available output range, limited by the saturation voltage of
the output transistors. The saturation voltage increases with the
drive current that the output transistor is required to supply due
to the collector resistance of the output transistor.
As the saturation point of the output stage is approached, the
output signal shows increasing amounts of compression and
clipping. As in the input headroom case, higher frequency
signals require slightly more headroom than the lower fre-
quency signals. Figure 16 illustrates this point by plotting the
typical harmonic distortion vs. the output amplitude.
OVERLOAD BEHAVIOR AND RECOVERY
Input
The specified input common-mode voltage of the ADA4851-1/
ADA4851-2/ADA4851-4 is 200 mV below the negative supply
to within 2.2 V of the positive supply. Exceeding the top limit
results in lower bandwidth and increased rise time, as shown in
Figure 41 and Figure 42. Pushing the input voltage of a unity-
gain follower to less than 2 V from the positive supply leads to
the behavior shown in Figure 43—an increasing amount of output
error as well as a much increased settling time. The recovery time
from input voltages of 2.2 V or closer to the positive supply is
approximately 55 ns, which is limited by the settling artifacts
caused by transistors in the input stage coming out of saturation.
ADA4851-1/ADA4851-2/ADA4851-4
Figure 42. Output Rising Edge for 1 V Step at Input Headroom Limits
3.4
3.2
3.0
2.8
2.6
2.4
2.2
2.0
1.8
3.6
0
G = +1
R
V
L
S
= 1kΩ
= 5V
10
20
30
V
V
V
V
V
STEP
STEP
STEP
STEP
STEP
40
= 2.1V TO 3.1V
= 2V TO 3V
= 2.2V TO 3.2V
= 2.3V TO 3.3V
= 2.4V TO 3.4V
TIME (ns)
50
60
70
80
90
100
Rev. J | Page 18 of 24
The amplifiers do not exhibit phase reversal, even for input
voltages beyond the voltage supply rails. Going more than 0.6 V
beyond the power supplies turns on protection diodes at the input
stage, which greatly increases the current draw of the devices.
Output
Output overload recovery is typically within 35 ns after the
input of the amplifier is brought to a nonoverloading value.
Figure 44 shows output recovery transients for the amplifier
configured in an inverting gain of 1 recovering from a saturated
output from the top and bottom supplies to a point at midsupply.
Figure 43. Pulse Response of G = +1 Follower, Input Step Overloading
3.50
3.25
3.00
2.75
2.50
2.25
2.00
–1
–2
6
5
4
3
2
1
0
7
0
0
G = +1
R
V
INPUT
VOLTAGE
EDGES
L
S
100
10
= 1k Ω
= 5V
200
20
Figure 44. Overload Recovery
300
30
V
STEP
the Input Stage
400
40
= 2.25V TO 3.25V
TIME (ns)
TIME (ns)
V
3.5V, 4V, AND 5V
STEP
V
500
50
OUT
= 2.25V TO
= 5V TO 2.5V
600
60
V
OUT
700
70
= 0V TO 2.5V
800
80
G = –1
R
V
L
S
900
= 1kΩ
= 5V
90
100
1k