ADCLK846BCPZ Analog Devices Inc, ADCLK846BCPZ Datasheet - Page 12

• Manufacturer Part Number: ADCLK846BCPZ
• Description: 1.8V 6LVDS/12 CMOS Clock Fanout Buffer
• Manufacturer: Analog Devices Inc
• Type: Fanout Buffer (Distribution)r

Specifications of ADCLK846BCPZ

• Design Resources: Synchronizing Multiple AD9910 1 GSPS Direct Digital Synthesizers (CN0121)
• Number Of Circuits: 1
• Ratio - Input:output: 1:6
• Differential - Input:output: Yes/Yes
• Input: CML, CMOS, HSTL, LVDS, LVPECL
• Output: CMOS, LVDS
• Frequency - Max: 1.2GHz
• Voltage - Supply: 1.71 V ~ 1.89 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 24-LFCSP
• Frequency-max: 1.2GHz
• Number Of Outputs: 12
• Operating Supply Voltage (max): 1.89V
• Operating Temp Range: -40C to 85C
• Propagation Delay Time: 4.2ns
• Operating Supply Voltage (min): 1.71V
• Mounting: Surface Mount
• Pin Count: 24
• Operating Supply Voltage (typ): 1.8V
• Package Type: LFCSP EP
• Input Frequency: 1.2GHz
• Operating Temperature Classification: Industrial
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

ADCLK846
CLOCK OUTPUTS
Each driver consists of a differential LVDS output or two single-
ended CMOS outputs (always in phase). When the LVDS driver
is enabled, the corresponding CMOS driver is in tristate. When
the CMOS driver is enabled, the corresponding LVDS driver is
powered down and tristated. Figure 21 and Figure 22 display
the equivalent output stage.
CONTROL AND FUNCTION PINS
Logic Select for CTRL_A
CTRL_A selects either CMOS (high) or LVDS (low) logic for
Output 1 and Output 0. This pin has an internal 200 kΩ pull-
down resistor.
Logic Select for CTRL_B
CTRL_B selects either CMOS (high) or LVDS (low) logic for
Output 5, Output 4, Output 3, and Output 2. This pin has an
internal 200 kΩ pull-down resistor.
Sleep Mode
SLEEP powers down the chip except for the band gap. The
input is active high, which puts the outputs into a high-Z state.
This pin has a 200 kΩ pull-down resistor. The control pins are
operational during sleep mode.
Figure 21. LVDS Output Simplified Equivalent Circuit
Figure 22. CMOS Equivalent Output Circuit
V
S
3.5mA
3.5mA
OUTxA
V
S
OUTx
OUTx
V
S
OUTxB
Rev. B | Page 12 of 16
POWER SUPPLY
The ADCLK846 requires a 1.8 V ± 5% power supply for V
Best practice recommends bypassing the power supply on
the PCB with adequate capacitance (>10 μF) and bypassing
all power pins with adequate capacitance (0.1 μF) as close to
the part as possible. The layout of the ADCLK846 evaluation
board (ADCLK846/PCBZ) provides a good layout example.
Exposed Metal Paddle
The exposed metal paddle on the ADCLK846 package is an
electrical connection, as well as a thermal enhancement. For
the device to function properly, the paddle must be properly
attached to ground (GND). The ADCLK846 dissipates heat
through its exposed paddle. The PCB acts as a heat sink for the
ADCLK846. The PCB attachment must provide a good thermal
path to a larger heat dissipation area, such as the ground plane
on the PCB. This requires a grid of vias from the top layer down
to the ground plane. See Figure 23 for an example.
Figure 23. PCB Land Example for Attaching Exposed Paddle
VIAS TO GND PLANE
S
.