AM29F016D-70EI Spansion Inc., AM29F016D-70EI Datasheet - Page 15

• Manufacturer Part Number: AM29F016D-70EI
• Description: IC,EEPROM,NOR FLASH,2MX8,CMOS,TSSOP,48PIN,PLASTIC
• Manufacturer: Spansion Inc.

Specifications of AM29F016D-70EI

• Rohs Compliant: NO

COMMON FLASH MEMORY INTERFACE
(CFI)
The Common Flash Interface (CFI) specification out-
lines device and host system software interrogation
handshake, which allows specific vendor-specified
software algorithms to be used for entire families of de-
v i c e s. S o f t wa r e s u p p o r t c a n t h e n b e d ev i c e -
independent, JEDEC ID-independent, and forward-
and backward-compatible for the specified flash device
families. Flash vendors can standardize their existing
interfaces for long-term compatibility.
This device enters the CFI Query mode when the sys-
tem writes the CFI Query command, 98h, to address
55h, any time the device is ready to read array data.
November 1, 2006 21444E6
Addresses
Addresses
1Ch
1Dh
1Ah
1Bh
1Eh
1Fh
10h
11h
12h
13h
14h
15h
16h
17h
18h
19h
20h
21h
22h
23h
24h
25h
26h
Data
Data
51h
52h
59h
02h
00h
40h
00h
00h
00h
00h
00h
45h
55h
00h
00h
03h
00h
0Ah
00h
05h
00h
04h
00h
Table 5. CFI Query Identification String
Query Unique ASCII string “QRY”
Primary OEM Command Set
Address for Primary Extended Table
Alternate OEM Command Set (00h = none exists)
Address for Alternate OEM Extended Table (00h = none exists)
V
D7–D4: volt, D3–D0: 100 millivolt
V
D7–D4: volt, D3–D0: 100 millivolt
V
V
Typical timeout per single byte/word write 2
Typical timeout for Min. size buffer write 2
Typical timeout per individual block erase 2
Typical timeout for full chip erase 2
Max. timeout for byte/word write 2
Max. timeout for buffer write 2
Max. timeout per individual block erase 2
Max. timeout for full chip erase 2
Table 6. System Interface String
CC
CC
PP
PP
Min. voltage (00h = no V
Max. voltage (00h = no V
Min. (write/erase)
Max. (write/erase)
D A T A
Am29F016D
S H E E T
The system can read CFI information at the addresses
given in Tables 5–8. To terminate reading CFI data, the
system must write the reset command.
The system can also write the CFI query command
when the device is in the autoselect mode. The device
enters the CFI query mode, and the system can read
CFI data at the addresses given in Tables 5–8. The sys-
tem must write the reset command to return the device
to the autoselect mode.
For further information, please refer to the CFI Specifi-
cation and CFI Publication 100, available via the World
Wide Web at http://www.amd.com/products/nvd/over-
v i ew / c f i . h t m l . A l t e r n a t i ve l y, c o n t a c t a n A M D
representative for copies of these documents.
PP
PP
N
times typical
pin present)
N
pin present)
N
N
times typical (00h = not supported)
Description
Description
times typical
ms (00h = not supported)
N
N
times typical
N
N
µs (00h = not supported)
ms
µs
13