AM29LV160DB-90EC Spansion Inc., AM29LV160DB-90EC Datasheet - Page 16
![no-image](/images/manufacturer_photos/0/6/621/spansion_inc__sml.jpg)
AM29LV160DB-90EC
Manufacturer Part Number
AM29LV160DB-90EC
Description
Flash Memory IC
Manufacturer
Spansion Inc.
Datasheet
1.AM29LV160DB-90EC.pdf
(52 pages)
Specifications of AM29LV160DB-90EC
Memory Configuration
2M X 8 / 1M X 16 Bit
Package/case
48-TSOP
Supply Voltage Max
3.6V
Leaded Process Compatible
No
Peak Reflow Compatible (260 C)
No
Access Time, Tacc
90nS
Supply Voltage
3V
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AM29LV160DB-90EC
Manufacturer:
AMD
Quantity:
550
Part Number:
AM29LV160DB-90EC
Manufacturer:
AMD
Quantity:
20 000
Autoselect Mode
The autoselect mode provides manufacturer and de-
vice identification, and sector protection verification,
through identifier codes output on DQ7–DQ0. This
mode is primarily intended for programming equip-
m e n t t o a u t o m a t i c a l l y m a t c h a d ev i c e t o b e
programmed with its corresponding programming al-
gorithm. However, the autoselect codes can also be
accessed in-system through the command register.
When using programming equipment, the autoselect
mode requires V
A9. Address pins A6, A1, and A0 must be as shown in
L = Logic Low = V
Note: The autoselect codes may also be accessed in-system via command sequences. See Table 9.
Sector Protection/Unprotection
The hardware sector protection feature disables both
program and erase operations in any sector. The hard-
ware sector unprotection feature re-enables both
program and erase operations in previously protected
sectors.
The device is shipped with all sectors unprotected.
AMD offers the option of programming and protecting
sectors at its factory prior to shipping the device
through AMD’s ExpressFlash™ Service. Contact an
AMD representative for details.
It is possible to determine whether a sector is pro-
tected or unprotected. See “Autoselect Mode” for
details.
Sector protection/unprotection can be implemented
via two methods.
14
Manufacturer ID: AMD
Device ID:
Am29LV160D
(Top Boot Block)
Device ID:
Am29LV160D
(Bottom Boot Block)
Sector Protection Verification
Description
IL
ID
, H = Logic High = V
(11.5 V to 12.5 V) on address pin
Mode
Word
Word
Byte
Byte
Table 4. Am29LV160D Autoselect Codes (High Voltage Method)
CE#
L
L
L
L
L
L
OE#
IH
L
L
L
L
L
L
, SA = Sector Address, X = Don’t care.
WE#
H
H
H
H
H
H
D A T A
A19
A12
SA
to
X
X
X
Am29LV160D
A11
A10
to
X
X
X
X
S H E E T
Table 4. In addition, when verifying sector protection,
the sector address must appear on the appropriate
highest order address bits (see Tables 2 and 3). Table
4 shows the remaining address bits that are don’t
care. When all necessary bits have been set as re-
quired, the programming equipment may then read the
corresponding identifier code on DQ7-DQ0.
To access the autoselect codes in-system, the host
system can issue the autoselect command via the
command register, as shown in Table 9. This method
does not require V
details on using the autoselect mode.
The primary method requires V
only, and can be implemented either in-system or via
programming equipment. Figure 2 shows the algo-
rithms and Figure 23 shows the timing diagram. This
method uses standard microprocessor bus cycle tim-
ing. For sector unprotect, all unprotected sectors must
first be protected prior to the first sector unprotect
write cycle.
The alternate method intended only for programming
equipment requires V
This method is compatible with programmer routines
written for earlier 3.0 volt-only AMD flash devices. De-
tails on this method are provided in a supplement,
publication number 21468. Contact an AMD represen-
tative to request a copy.
V
V
V
V
A9
ID
ID
ID
ID
A8
A7
to
X
X
X
X
A6
L
L
L
L
A5
A2
to
X
X
X
X
ID
. See “Command Definitions” for
ID
A1
H
L
L
L
on address pin A9 and OE#.
A0
H
H
L
L
ID
DQ15
on the RESET# pin
DQ8
May 5, 2006 22358B7
22h
22h
to
X
X
X
X
X
(unprotected)
(protected)
DQ7
DQ0
C4h
C4h
01h
49h
49h
01h
00h
to