118577-000 TE Connectivity, 118577-000 Datasheet - Page 278
![no-image](/images/manufacturer_photos/0/6/654/te_connectivity_sml.jpg)
118577-000
Manufacturer Part Number
118577-000
Description
Cable Accessories Terminator
Manufacturer
TE Connectivity
Type
Sleever
Datasheet
1.163665N003.pdf
(637 pages)
Specifications of 118577-000
Body Material
Polyvinylidene Fluor
Product Diameter (mm)
7mm
Product Length (mm)
20.85mm
Lead Free Status / RoHS Status
Supplier Unconfirmed
- Current page: 278 of 637
- Download datasheet (13Mb)
5-6
Catalog 1654025
Revised 12-04
www.tycoelectronics.com
Dimensions are in millimeters
and inches unless otherwise
specified. Values in brackets
are U.S. equivalents.
Adhesives
Installation Guide
4. Double-wrap the tape
5. Center the molded part
6. Apply heat to the center
7. Continue heating each
8. Where oven curing is
around the abraded
areas of the cable,
placing slight tension
on the tape as you wrap.
Tack the ends in place
with a soldering iron or
hot tool.
over the transition area.
When properly posi-
tioned, the part should
not fit tightly in the
“branched” area of the
breakout. A tight fit may
cause the part to crease
or wrinkle as it recovers.
The tape should extend
slightly beyond the end
of the transition.
of the transition. Recover
one leg of the transition,
moving heat from the
center of the transition
to the adhesive opening
of the leg. Repeat the
procedure on each leg
of the transition.
end of the transition until
the part is fully recov-
ered and the adhesive
tape has properly
melted or flowed. The
tape should now appear
wet, form a bead or fillet
between the cable and
transition, and show no
definition between the
layers of tape.
required to complete
adhesive bonding, heat
the assembled harness
in a preheated oven
according to the
following schedule:
S-1255-02:
2 hours at 155°C [311°F]
S-1124:
90 minutes at 150°C [302°F]
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
(Continued)
Thermosets
Connector Boot
1. Thoroughly mix the two
2. Degrease the area of
3. Lightly abrade the
4. Lightly abrade back 25.4
5. Using a spatula, apply
6. Apply adhesive to the
7. With a clean cloth,
8. Follow the curing
parts according to the
instructions provided
with the kit.
the adapter to which
the boot will be bonded,
using appropriate
solvent on a paper
tissue or clean cloth. Do
not abrade the adapter.
bonding area of the
cable jacket with #320
emery cloth, then wipe
off loose particles with a
tissue or clean cloth.
mm [1.0] inside each
end of the boot.
the mixed adhesive to
the adapter and shrink
the boot to the end
of the adapter.
cable jacket and
complete the shrinking
process.
remove excess adhesive
from all areas
immediately.
conditions outlined in
this guide.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
Transition
1. Thoroughly mix the two
2. Lightly abrade the
3. Abrade and wipe inside
4. Using a spatula, apply
5. Apply heat to the center
6. Remove excess
7. Follow the curing
South America: 55-11-3611-1514
Japan: 81-44-900-5102
Singapore: 65-4866-151
UK: 44-1793-528171
parts according to the
instructions provided
with the kit.
bonding area of the
cable jacket with #320
emery cloth, then wipe
off loose particles with a
tissue or clean cloth.
each opening of the
transition.
the mixed adhesive to
the cable jacket.
of the transition. Recover
one leg of the transition,
moving heat from the
center of the transition
to the adhesive opening
of the leg. Repeat the
procedure on each leg.
adhesive from all areas
immediately with a
clean cloth.
conditions specified
for “thermosets” in the
“Adhesive/Sealant
Product Characteristics
Table” on pages 5-2 and
5-3.