MTCMR-G2-GP-ED Multi-Tech Systems, MTCMR-G2-GP-ED Datasheet - Page 43
![no-image](/images/no-image-200.jpg)
MTCMR-G2-GP-ED
Manufacturer Part Number
MTCMR-G2-GP-ED
Description
MODEM CELLULAR QUAD GPRS
Manufacturer
Multi-Tech Systems
Series
MultiModem® iCellr
Datasheets
1.SF100-G.pdf
(4 pages)
2.MTCMR-E1.pdf
(16 pages)
3.MTCMR-E1.pdf
(79 pages)
4.MTCMR-E1.pdf
(2 pages)
5.MTCMR-E1.pdf
(2 pages)
Specifications of MTCMR-G2-GP-ED
Function
Transceiver, GPRS, Modem
Modulation Or Protocol
GPRS
Frequency
900MHz, 1.8GHz
Applications
General Purpose
Interface
RS-232, USB
Sensitivity
-161dB
Data Rate - Maximum
85.6kbps
Voltage - Supply
9 V ~ 32 V, USB
Package / Case
Module
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
881-1117
6 1 B P acket Filters > DNAT Configuration
9 0 B
Destination Network Address Translation (DNAT) is a process that allows the placing of servers within the protected network
and making them available for a certain service to the outside world. The DNAT process running on the router translates the
destination address of incoming packets to the address of the real network server on the LAN. The packets are then forwarded.
You can Delete or Edit a DNAT rule after it has been defined and added by using the table at the bottom of the screen.
Important Note:
Packet Filters > DNAT Example
Set Up DNAT and Port Forwarding to an Internal Device
Multi-Tech Systems, Inc. MultiModem rCell User Guide
DNAT Configuration
Note:
Situation:
7700.
Allow Access:
External Service:
LAN IP:
Internal Service:
Internal Source:
Save Button:
1.
2.
The internal device can be camera, meter, security device, etc.
On the
On the
service will be a meter.
Assume the device is on a LAN with an IP address of 192.168.2.100 and the port to access the device is port
When adding rules, at least one host must be defined in the Network Configuration section.
Name –
IP Address and Subnet Address –
Add –
Name –
Protocol –
S-Port / Client –
D-Port / Server –
Add –
Network & Services > Network Configuration
Network & Services > Service Configuration
Click the Add button to save this configuration.
Click the Add button to save this configuration.
Enter a name for the LAN device.
Enter a name for the service (use a name that will identify the service for you).
Example:
Example:
Example:
Example:
Example:
Select a protocol.
Select a network or host to which IP packets will be allowed and re-routed. The network/host
must be pre-defined in the Network Configuration section.
Select the External Service that you want allowed. The service must be defined in the Service
Configuration section.
Select the LAN IP to which the packets are to be diverted. Only one host can be defined as the
destination.
Select the Internal Service to be the destination.
Select the source address for packets that are going to be sent. If you do not want to change the
address, select NOCHANGE.
Click the Save button. The defined DNAT configuration is added and will display at the bottom of
the screen. Entries can be deleted or edited by clicking the Edit or the Delete buttons.
Enter the source port for this service.
Enter the destination port for this service.
MeterPort
Name = MeterIP
IP Address = 192.168.2.100
Subnet Address = 255.255.255.255. The subnet mask in the network configuration is not
defined using x.x.x.x notation. It uses ‘bit’ notation. So 255.255.255.255 = 32.
tcp or udp
1:65535
7700
Enter the IP address and subnet address of the device.
screen, define a service name. For this example, the
screen, set up the following parameters:
Chapter 4 – Using the Web Management Software
43