MT9P031I12STM Aptina LLC, MT9P031I12STM Datasheet - Page 4

• Manufacturer Part Number: MT9P031I12STM
• Description: SENSOR IMAGE 5MP MONO CMOS 48LCC
• Manufacturer: Aptina LLC
• Type: CMOS Imagingr

Specifications of MT9P031I12STM

• Package / Case: 48-iLCC
• Pixel Size: 2.2µm x 2.2µm
• Active Pixel Array: 2592H x 1944V
• Frames Per Second: 60
• Voltage - Supply: 2.6 V ~ 3.1 V
• Supply Voltage Range: 1.7V To 3.1V, 1.7V To 1.9V, 2.6V To 3.1V
• Operating Temperature Range: -30°C To +70°C
• Digital Ic Case Style: PLCC
• No. Of Pins: 48
• Supply Voltage Max: 3.1V
• Ic Function: Digital Image Sensor
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 557-1430 - KIT HEAD BOARD FOR MT9P031557-1429 - KIT DEV FOR MT9P031
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 557-1397; Q3884047; Q3956538; Q4007187

Table 3:
PDF: 09005aef824c997f/Source: 09005aef824c998a
MT9T031_3100_PB_2.fm - Rev. A 8/06 EN
15, 17, 18, 21, 47, 48
2, 3, 6, 9, 11,14,19,
24, 25, 26, 27, 28,
32, 33, 34, 35, 36
Pin Numbers
5, 23, 38, 43
.
30 42, 44
4, 22, 37
16, 20
10
13
29
46
12
45
31
39
40
41
7
8
1
Pin Descriptions
FRAME_VALID
LINE_VALID
GSHT_CTL
STANDBY
D
TRIGGER
Symbol
STROBE
EXTCLK
VAAPIX
RESET#
PIXCLK
OUT
S
D
A
SCLK
OE#
V
V
DATA
NC
GND
GND
DD
AA
[9:0]
Output
Output
Output
Output
Output
Supply
Supply
Supply
Supply
Supply
Input
Input
Input
Input
Input
Input
Type
Input
I/O
–
Standby: Activates (HIGH) standby mode, disables analog bias circuitry
for power saving mode.
Trigger: Activates (HIGH) snapshot sequence.
Reset: Activates (LOW) asynchronous reset of sensor. All registers
assume factory defaults.
Output enable: OE# when HIGH, places outputs D
FRAME_VALID, LINE_VALID, PIXCLK, and STROBE into a tri-state
configuration.
Clock in: Master clock into sensor (48 MHz maximum).
Serial clock: Clock for serial interface.
Global shutter control.
Serial data: Serial data bus, requires 1.5K
Data out: Pixel data output bit 0, D
Pixel clock: Pixel data outputs are valid during falling edge of this
clock. Frequency = master clock.
Strobe: Output is pulsed HIGH to indicate sensor reset operation of
pixel array has completed.
Line valid: Output is pulsed HIGH during line of selectable valid pixel
data (see R0x20 for options).
Frame valid: Output is pulsed HIGH during frame of valid pixel data.
Analog pixel power: Provides power supply for pixel array, 3.3V
±0.3V.
Digital power: Provides power supply for digital block, 3.3V ±0.3V.
Digital ground: Provides isolated ground for digital block.
Analog power: Provides power supply for analog block, 3.3V ±0.3V.
Analog ground: Provides isolated ground for analog block and pixel
array.
No connect: These pins must be left unconnected.
MT9T031: 1/2-Inch 3-Mp Digital Image Sensor
3
Micron Technology, Inc., reserves the right to change products or specifications without notice.
Description
OUT
[9] (MSB), D
Ω
resistor to 3.3V for pull-up.
General Description
©2006 Micron Technology, Inc. All rights reserved.
OUT
OUT
[9:0],
[0] (LSB).