B3J-6100 Omron, B3J-6100 Datasheet - Page 7

• Manufacturer Part Number: B3J-6100
• Description: MECHANICAL KEY SWITCH
• Manufacturer: Omron
• Series: B3Jr
• Type: Keyswitch, Illuminatedr

Specifications of B3J-6100

• Circuit: SPST-NO
• Switch Function: Off-Mom
• Contact Rating @ Voltage: 0.05A @ 24VDC
• Actuator Type: Square Button
• Illumination Type, Color: LED, Red/ Green
• Illumination Voltage (nominal): 2.0, 2.1 VDC
• Mounting Type: Through Hole
• Termination Style: PC Pin
• Operating Force: 130 g +/- 50 g
• Actuator: Key Cap
• Contact Current Rating: 1 mAmp to 50 mAmps at 5 Volts to 24 Volts
• Contact Form: SPST - NO
• Body Size: 18 mm L x 12 mm W x 10.3 mm H
• Color: Black
• Features: Tactile Switch with Integral Key Cap
• Mounting Style: PCB
• Operating Temperature Range: - 25 C to + 70 C
• Contact Rating: 1 mAmp to 50 mAmps at 5 Volts to 24 Volts
• Contact Configuration: SPST-NO
• Contact Voltage Dc Nom: 24V
• Contact Current Max: 50mA
• Actuation Type: Top
• Switch Terminals: PCB / Push-on
• Circuitry: SPST-NO
• Rohs Compliant: Yes
• Actuator / Cap Color: Black
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: B3J6100; SW826; Z2183; Z2183

Precautions
B3FS-1050P
B3S
Note:
Standards
Package
Heat resistance
Standards
Package
Heat resistance
Tape drawing direction
Switches with ground terminals are packaged with the
ground terminal on the opposite side of the guide hole.
1.5
8.7
+0.1
0
dia.
0.06
Reel
Reel (made of paper)
7
(22)
1.5
+0.1
12±
0
13 dia.
4±
dia.
Tape drawing direction
Label
0.1
Conforms to JEITA.
1,000 Switches
60 ° C for 24 hours (without deformation)
Conforms to JEITA.
1,000 Switches
50 ° C for 24 hours (without deformation)
0.1
9.4
1.5
12±
2
4±
Tape drawing direction
0.1
Tape drawing direction
0.1
1.75±
0.4
380±2 dia.
7.5
Label
0.1
2
330 dia.
16±
4.7
13 dia.
0.3
1.75
7.5
(8.1)
16
21.5
LEDs (B3J)
Make sure that the polarity of the LEDs is correct. The polarity is
not indicated on the Switch, but the positive pole is located on the
back surface of the Switch on the side without the OMRON mark.
Connect limiting resistors to the LEDs. The Switch does not have
built-in limiting resistors, so satisfy the LED characteristics by
obtaining the limiting resistance according to the following formula
based on the voltage to be used.
Limiting resistance (R)=
0.5
50
30
10
50
40
30
20
10
5
3
1
0
−20
1.5
1.6
(Voltage used (E) – LED forward voltage (VF))
R
0
1.7
E
Green
Yellow
LED forward current (IF)
20
Red
I
V
F
F
Ambient temperature Ta (°C)
1.8
40
Forward voltage V
1.9
Red
Yellow/Green
60
Precautions
2.0
F
2.1
(V)
80
(Ω)
7