G6AU-234P-ST10-US DC5 Omron, G6AU-234P-ST10-US DC5 Datasheet - Page 8

• Manufacturer Part Number: G6AU-234P-ST10-US DC5
• Description: LOW SIGNAL RELAY
• Manufacturer: Omron
• Series: G6Ar

Specifications of G6AU-234P-ST10-US DC5

• Relay Type: General Purpose
• Circuit: DPDT (2 Form C)
• Contact Rating @ Voltage: 1A @ 30VDC
• Coil Type: Latching, Single Coil
• Coil Current: 20mA
• Coil Voltage: 5VDC
• Control On Voltage (max): 3.5 VDC
• Mounting Type: Through Hole
• Termination Style: PC Pin
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Control Off Voltage (min): -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: G6AU-234P-ST10-USDC5; G6AU234PST10USDC5

G6AK-274P-ST(40)-US
G6AU-474P-ST-US
G6AK-474P-ST(40)-US
Precautions
Long-term Continuously ON Contacts
Using the Relay in a circuit where the Relay will be ON continuously
for long periods (without switching) can lead to unstable contacts
because the heat generated by the coil itself will affect the insulation,
causing a film to develop on the contact surfaces. Be sure to use a
fail-safe circuit design that provides protection against contact failure
or coil burnout. Otherwise, use a latching relay.
88
Low Signal Relay
- DISCONTINUED
- DISCONTINUED
0.6
20.2 max.
(20)*
0.6
G6A
0.6
*Average value
35.4 max.
(35.2)*
0.3
35.4 max.
(35.2)*
10.1 max.
(9.9)*
7.62
*Average value
0.64
*Average value
0.3
8.4 max.
(8.2)*
3.16
0.3
10.1 max.
(9.9)*
7.62
10.1 max.
(9.9)*
Terminal Arrangement/
Internal Connections
(Bottom View)
16
Relay Handling
When washing the product after soldering the Relay to a PCB, use a
water-based solvent or alcohol-based solvent, and keep the solvent
temperature to less than 40°C. Do not put the Relay in a cold clean-
ing bath immediately after soldering.
1
7.62
+
-
S R
+
-
0.64
Fourteen, 1.0-dia. holes
Sixteen, 1.0-dia. holes
15
2
0.64
4
13
8.4 max.
(8.2)*
3.16
11
6
8.4 max.
(8.2)*
3.16
(1.2)
9
8
5.08 5.08 5.08 2.54
10
5.08 5.08 5.08
Terminal Arrangement/
Internal Connections
(Bottom View)
7
Terminal Arrangement/
Internal Connections
(Bottom View)
10
Tolerance: ±0.1
7
Mounting Holes
(Bottom View)
Tolerance: ±0.1
Mounting Holes
(Bottom View)
(1.2)
Ten, 1-dia. holes
12
5
12
5
Mounting Holes
(Bottom View)
Tolerance: ±0.1
14
2.54
3
S
14
3
+
-
16
1
5.08
7.62
16
1
5.08
+ -
15
2
S R
- +
13
+
-
R
4
5.08 5.08
13
5.08 5.08
4
5.08 5.08
11
6
11
6
9
8
9
8
(1.2)
7.62
(1.2)
(1.2)
(1.2)
7.62
(1.2)
7.62
(1.2)
(1.2)
(1.2)
(1.2)