VX-015-1C23 Omron, VX-015-1C23 Datasheet - Page 6
![MINIATURE BASIC SWITCH](/photos/15/24/152480/vx-015-1c23_sml.jpg)
VX-015-1C23
Manufacturer Part Number
VX-015-1C23
Description
MINIATURE BASIC SWITCH
Manufacturer
Omron
Series
VXr
Specifications of VX-015-1C23
Circuit
SPDT
Switch Function
On-Mom
Contact Rating @ Voltage
0.1A @ 125VAC
Actuator Type
Lever, Roller
Mounting Type
Chassis Mount
Termination Style
Quick Connect - .187" (4.7mm)
Operating Force
50gf
Contact Form
SPDT
Contact Rating
0.1 Amp
Actuator
Hinge Roller Lever
Pole Throw Configuration
SPDT
Switch Function Configuration
N.O./N.C.
Actuator Style
Hinge Roller Lever
Current Rating (max)
0.1A
Ac Voltage Rating (max)
125VVAC
Dc Voltage Rating (max)
30VVDC
Contact Material
Gold Alloy
Mechanical Life
10000000
Terminal Type
Quick Connect
Product Height (mm)
28mm
Product Depth (mm)
10.3mm
Product Length (mm)
37.8mm
Operating Temp Range
-25C to 80C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
SW876
VX-015-1C23
VX0151C23
VX-015-1C23
VX0151C23
Precautions
■ Correct Use
Mounting Direction
For a switch with an actuator, mount the switch in a direction where
the actuator weight will not be applied to the switch.
Since the switch is designed for a small load, its resetting force is
small. Therefore, resetting failure may occur if unnecessary load is
applied to the switch.
Operation
Keep the operation control completely separate from the actuator of
the switch, and push it down fully when starting operation. Do not dis-
place the operating position of the actuator when machining.
Consult OMRON in advance if the operating speed is to be extremely
slow, or if the pushbutton is to be set somewhere between the free
position and operating position.
Mount pin pushbutton switches so that stroke of the pushbutton and
the stroke of the operating control overlap on a vertical line. The
stroke of the switch, after operation, should be set to 60- 90% that of
standard OT (MIN operation).
Using Microloads
Using a model for ordinary loads to switch microloads may result in
faulty operation. Instead, use the models that are designed for micro-
loads and that operate in the following range;
However, even when using microload models within the operating
range shown above, if inrush current or inductive voltage spikes
occur when the contact is opened or closed, it may increase contact
wear and so decrease the service life. Therefore, insert a contact
protection circuit where necessary.
140
12
30
24
5
0
0.1
Snap Action Switch
0.16mA
Inoperable
range
1mA
1
Operating range
for micro load
models VX-01
10
26mA
VX
100mA 160mA
100mA
Current (mA)
100
Operating
range for
general-
load models
VX-5
1,000
■ Cautions
Handling
Be careful not to drop the switch. Doing so may cause damage to the
switch’s internal components because it is designed for a small load.
Solder Terminal Connection
Quickly finish the soldering of the lead wire to its terminal. Use a sol-
dering iron rated at 60W and preferably complete the soldering within
5 seconds.
Excess wattage or prolonged heating can deteriorate the characteris-
tics of the switch.
Insulation Distance
When mounting, make sure there is sufficient insulation distance
between the switch and its mounting panel. If it is insufficient, install
an insulation guard or separator. Always install an insulation guard or
separator when mounting the microswitch on a metallic body. Con-
tact your OMRON representative for information about insulation
guards and separators.
Application Environment
Do not use the Switch in locations that are subject to toxic gas, sili-
con, excessive dust, excessive dirt, high temperatures, high humidity,
sudden temperature changes, water splashes, or oil splashes.
Otherwise, damage resulting by faulty contact of the Switch contacts,
corrosion, or other causes, or other functional faults may occur.
Depending on environmental conditions, the switch should be
rechecked about 3 to 6 months after it has been assembled.