Z-15GQ22-B Omron, Z-15GQ22-B Datasheet - Page 24
![BASIC SWITCH](/photos/15/31/153199/z15gq22-b_sml.jpg)
Z-15GQ22-B
Manufacturer Part Number
Z-15GQ22-B
Description
BASIC SWITCH
Manufacturer
Omron
Series
Zr
Type
Snap Actionr
Specifications of Z-15GQ22-B
Circuit
SPDT
Switch Function
On-Mom
Contact Rating @ Voltage
15A @ 125VAC
Actuator Type
Roller Plunger
Mounting Type
Panel Mount
Termination Style
Screw Terminal
Operating Force
350gf
Contact Form
SPDT
Contact Rating
15 Amps at 250 Volts
Actuator
Plunger, Roller
Post Position
Standard
Microswitch Type
Standard
Actuator Style
Roller Plunger
Operating Force Max
350gf
Contact Voltage Ac Nom
250V
Contact Voltage Dc Nom
250V
Contact Current Max
15A
Switch Terminals
Screw
Mounting
Panel
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
SW1074
SW1074
SW194
Z-15GQ22-B7-K
Z-15GQ22-B7-K
Z15GQ22-B
Z15GQ22-B7-K
Z15GQ22B
Z15GQ22B7K
SW1074
SW194
Z-15GQ22-B7-K
Z-15GQ22-B7-K
Z15GQ22-B
Z15GQ22-B7-K
Z15GQ22B
Z15GQ22B7K
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
Z-15GQ22-B
Manufacturer:
OMRON
Quantity:
1 000
Tightening
The suitable tightening torque for screw terminals is given below.
Operation
• Make sure that the switching speed and frequency are is within the
1. If the switching speed is extremely slow, the contacts may not be
2. If the switching speed is extremely fast, switching shock may
• Make sure that the actuator travel does not exceed the permissible
Panel Mount Switch (Z-15@Q@, Z-01@Q@)
• When mounting the panel mount plunger model with screws on a
• When using the panel mount plunger model mounted with screws
• When using the panel mount plunger model mounted with screws
High-sensitivity Switch (Z-15H)/
Extra-high-sensitivity Switch (Z-15H2)
• When using the Switch in a DC circuit, be sure to provide an arc
• In an application where a high repeat accuracy is required, limit the
• Do not apply a force of 19.6 N or higher to the pin plunger.
• Exercise care that the environment conditions such as temperature
170
specified ranges.
OT position. The operating stroke must be set to 70% to 100% of
the rated OT.
side surface, be careful of the dog angle and operation speed.
Excessive dog angle or operation speed may damage the Switch.
on a side surface, be careful not to apply a large shock. Applying a
shock exceeding 1,000 m/s
on a side surface, remove the hexagonal nuts from the actuator.
suppressor as well because the small contact gap of the Switch
may result in contact troubles.
current that flows through the Switch to within 0.1 A. Also, use a
relay to control a high-capacity load if the Switch is connected to
such a load. (In this case, the exciting current of the relay coil is the
load of the Switch.)
and humidity do not change abruptly.
• Screw terminals except for those on Split-contact Models
• Screw terminals on Split-contact Models
switched smoothly, which may result in a contact failure or contact
welding.
damage the Switch prematurely. If the switching frequency is too
high, the contacts may not be able to keep up with the speed.
The rated permissible switching speed and frequency indicate the
switching reliability of the Switch.
The life of a Switch is determined at the specified switching
speed. The life varies with the switching speed and frequency
even when they are within the permissible ranges.
Always conduct appropriate durability tests under actual condi-
tions before using a Switch.
(Z-10FY-B): 0.78 to 1.18 N·m
(Z-10FY-B): 0.49 to 1.18 N·m
General-purpose Basic Switch
2
may damage the Switch.
Z
Micro Load Applicable Range
Using a model for ordinary loads to open or close the contact of a
micro load circuit may result in faulty contact. Use models that
operate in the following range. However, even when using micro load
models within the operating range shown here, if inrush current
occurs when the contact is opened or closed, it may increase contact
wear and so decrease durability. Therefore, insert a contact
protection circuit where necessary.
The minimum applicable load is the N-level reference value. This
value indicates the malfunction reference level for the reliability level
of 60% (λ
the estimated malfunction rate is less than 1/2,000,000 operations
with a reliability level of 60%.
Models with Drip-proof Terminal Cover (Z-@A55-B5V) Wiring
• To attach the Protective Cover to the case, hold the cover in almost
Rubber packing
• Use round solderless terminals having the following dimensions to
• A cable 8.5 to 10.5 mm in diameter can be applicable to the sealing
• M4 small screws with spring toothed washer are used as the termi-
Terminal with
toothed
washer
Minimum applicable load
parallel to the case and then push it to the case. If the cover is
pushed diagonally, the rubber packing may slip off, degrading the
sealability of the Switch.
connect leads to the terminals. Tighten the screws of terminals to a
torque of 0.78 to 1.18 N·m. Use the terminal shown below.
rubber of the lead outlet of the Switch. A two-core or three-core
VCT cable having a cross-sectional area of 1.25 mm
suitable for this.
nal screws.
60
). The equation, λ
30
24
12
5
0
0.1
Unusable
range
5 mW
0.16 mA
1 mA
1
Operating range
for micro load
models Z-01H
60
20 max.
1 mA at 5 VDC
= 0.5×10
10
Z-01H
800 mW
4.3 dia.
26 mA
-6
100 mA 160 mA
/operations indicates that
8
100
Operating
range for
general load
models
Z-15H, H2
Z-15G
Z-15E
Z-10FY
Z-15ER
Current (mA)
160 mA at 5 VDC
Z-15@, Z-10FY
1,000
2
is especially