ADJ65006 PANASONIC EW, ADJ65006 Datasheet - Page 8

• Manufacturer Part Number: ADJ65006
• Description: ADJ(DJ) Relay (Flux, 2a, Single-side-sta
• Manufacturer: PANASONIC EW

REFERENCE DATA
1. Max. switching capacity
4. Set and Reset time
Sample: ADJ12024, 10 pcs
Coil applied voltage: 80 %V, 100 %V, 120 %V of rating
NOTES
1. Coil operating power
Pure DC current should be applied to the
coil. The wave form should be
rectangular. If it includes ripple, the ripple
factor should be less than 5%. However,
check it with the actual circuit since the
characteristics may be slightly different.
2. Coil connection
When connecting coils, refer to the wiring
diagram to prevent mis-operation or
malfunction.
3. Soldering
We recommend the following soldering
conditions
Soldering: 260°C±5°C 500°F±41°F,
max. 6 s
4. Others
1) If the relay has been dropped, the
appearance and characteristics should
always be checked before use.
2) The cycle lifetime is defined under the
standard test condition specified in the
JIS* C 5442-1996 standard (temperature
15 to 35°C
100
10
30
25
20
15
10
5
0
70
0
59 to
AC resistive load
(2-pole)
80
95°F, humidity 25 to
10
90
Coil applied voltage, %V
Contact voltage, V
100
AC resistive load
(1-pole)
100
110
120
Max.
x
Min.
All Rights Reserved © COPYRIGHT Matsushita Electric Works, Ltd.
130
1,000
2. Temperature rise
Sample: ADJ12024, 6 pcs.
Coil applied voltage: 0 %V, Contact current: 16 A, 20 A
Measured portion: Contact, Ambient temperature:
25°C 77°F, 85°C
5. Ambient temperature characteristics
Sample: ADJ12024, 6pcs
Ambient temperature: –40°C to 85°C
85%). Check this with the real device as it
is affected by coil driving circuit, load
type, activation frequency, activation
phase,ambient conditions and other
factors.
Also, be especially careful of loads such
as those listed below.
• When used for AC load-operating and
the operating phase is synchronous.
Rocking and fusing can easily occur due
to contact shifting.
• High-frequency load-operating
When high-frequency opening and
closing of the relay is performed with a
load that causes arcs at the contacts,
nitrogen and oxygen in the air is fused by
the arc energy and HNO
can corrode metal materials.
Three countermeasures for these are
listed here.
• Incorporate an arc-extinguishing circuit.
• Lower the operating frequency
• Lower the ambient humidity
3) For secure operations, the voltage
40
35
30
25
20
15
10
5
0
–60 –40 –20
0
185°F
5
0
10
Contact current, A
30
20
10
20
–10
–20
–30
3
15
40
is formed. This
Ambient
temperature, °C
–40°F to 185°F
60
20
+25°C
+85°C
Set
Reset
80 100
25
3. Coil temperature rise
Sample: ADJ56024, 6 pcs.
Coil applied voltage: 100 %V, 130 %V of rating
Contact current: 0 A, 10 A
Measured portion: Inside the coil, Ambient
temperature: Room temperature, 70°C
6. Influence of adjacent mounting
Sample: ADJ12024, 6pcs
Ambient temperature: Room temperature
applied to the coil should be nominal
voltage. In addition, please note that pick-
up and drop-out voltage will vary
according to the ambient temperature
and operation conditions.
4) Heat, smoke, and even a fire may
occur if the relay is used in conditions
outside of the allowable ranges for the
coil ratings, contact ratings, operating
cycle lifetime, and other specifications.
Therefore, do not use the relay if these
ratings are exceeded. Also, make sure
that the relay is wired correctly.
5) Incorrect wiring may cause
unexpected events or the generation of
heat or flames.
6) Check the ambient conditions when
storing or transporting the relays and
devices containing the relays. Freezing or
condensation may occur in the relay,
causing functional damage. Avoid
subjecting the relays to heavy loads, or
strong vibration and shocks.
–5
–5
50
40
30
20
10
5
0
5
0
0
90
0
2
100
Distance between relays , mm
Reset voltage
Set voltage
4
6
Coil applied voltage, %V
110
8
10
120
DJ (ADJ)
12
OFF
OFF
OFF
130
158°F
10A
room temperature
10A 70°C
0A
room temperature
0A 70°C
140