CUB30000 Red Lion Controls, CUB30000 Datasheet - Page 2

• Manufacturer Part Number: CUB30000
• Description: Counter
• Manufacturer: Red Lion Controls
• Series: CUB3r
• Type: Electronic Counterr

Specifications of CUB30000

• Count Rate: 100Hz
• Number Of Digits/alpha: 6
• Input Type: Switch Closure or Transistor Switch
• Voltage - Supply: 3V, 2 "N" Cell Batteries
• Display Type: LCD Non-Backlit
• Application: Electronic Counters
• Brand/series: CUB3
• Dimensions: 1.10 H × 2.09 W × 1.87 D Inches
• Display Digit Height: 0.2 Inches
• Mounting Type: Panel
• Number Of Digits: 6
• Primary Type: Counter
• Signal, Input: Switch Contact or Solid State Transistor
• Special Features: Self-Powered, Low-Cost/High Performance
• Termination: 12 Inch Leadwires
• Voltage, Supply: 3 Volt Batteries
• Available In Two Versions: Front Reset/Remote Reset
• Count Speed: 100 Counts/Sec
• Operating Temp.: –30°C to +75°C
• Weight: 3 Oz.
• Panel Cutout: 1" × 2"
• Digit Height: 5.1mm
• Operating Temperature Range: -30°C To +75°C
• No. Of Digits / Alpha: 6
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Output Type: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: CUB III; CUB-30-00; CUB-30-00/A; CUB-30-000/A; CUB3; RLC03

Red Lion Controls
Headquarters
20 Willow Springs Circle
York PA 17406
Tel [phone]
Fax [phone]
EMC INSTALLATION GUIDELINES
ElectroMagnetic Interference (EMI), proper installation and wiring methods
must be followed to ensure compatibility in each application. The type of the
electrical noise, source or coupling method into the unit may be different for
various installations. Listed below are some additional EMC guidelines for
successful installation in an industrial environment.
1. Use shielded (screened) cables for all Signal and Control inputs. The shield
2. Never run Signal or Control cables in the same conduit or raceway with AC
3. Signal or Control cables within an enclosure should be routed as far away as
Installation Environment
operating temperature and provides good air circulation. Placing the unit near
devices that generate excessive heat should be avoided.
Do NOT use solvents. Continuous exposure to direct sunlight may accelerate
the aging process of the bezel.
keypad of the unit.
Although this unit is designed with a high degree of immunity to
(screen) pigtail connection should be made as short as possible. The
connection point for the shield depends somewhat upon the application.
Listed below are the recommended methods of connecting the shield, in
order of their effectiveness.
a. Connect the shield only at the panel where the unit is mounted to earth
b. Connect the shield to earth ground at both ends of the cable, usually when
c. Connect the shield to common of the unit and leave the other end of the
power lines, conductors feeding motors, solenoids, SCR controls, and
heaters, etc. The cables should be run in metal conduit that is properly
grounded. This is especially useful in applications where cable runs are long
and portable two-way radios are used in close proximity or if the installation
is near a commercial radio transmitter.
possible from contactors, control relays, transformers, and other noisy
components.
The unit should be installed in a location that does not exceed the maximum
The bezel should be cleaned only with a soft cloth and neutral soap product.
Do not use tools of any kind (screwdrivers, pens, pencils, etc.) to operate the
ground (protective earth).
the noise source frequency is above 1 MHz.
shield unconnected and insulated from earth ground.
DIMENSIONS
NL - 3821 AD Amersfoort
Fax [phone]
Tel [phone]
TROUBLESHOOTING
numbers listed.
Red Lion Controls
For further technical assistance, contact technical support at the appropriate company
Printerweg 10
Europe
In inches (mm)
, INSTALLATION & BATTERY INSERTION
Ahmedabad-382480 Gujarat, India
4. In extremely high EMI environments, the use of external EMI suppression
5. Long cable runs are more susceptible to EMI pickup than short cable runs.
ELECTRICAL CONNECTIONS & COUNT INPUTS
switch contacts or solid-state switches (NPN or PNP transistors) as shown in
the diagrams below. Reed switches, mercury-wetted contacts, snap-action limit
switches, and silver alloy contacts with wiping action are usually satisfactory
choices for mechanical switch input. Heavy “clapper-type” contacts such as
used in contactors or large machine tool relays, tungsten contacts, or brush type
contacts are not recommended as count input devices.
Fax [phone]
GST Road, New Ranip,
PANEL CUT-OUT
PANEL THICKNESS
Tel [phone]
54, Vishvas Tenement
devices, such as ferrite suppression cores, is effective. Install them on Signal
and Control cables as close to the unit as possible. Loop the cable through the
core several times or use multiple cores on each cable for additional protection.
The following EMI suppression devices (or equivalent) are recommended:
Ferrite Suppression Cores for signal and control cables:
Therefore, keep cable runs as short as possible.
The CUB 3s can be supplied with count input signals from mechanical
1" x 2" or 25 MM x 50 MM
0.05" to 0.125"
Red Lion Controls
Fair-Rite # 0443167251 (RLC #FCOR0000)
TDK # ZCAT3035-1330A
Steward #28B2029-0A0
TO REMOVE REAR BATTERY COVER
INSERT BLADE OF SMALL SCREWDRIVER
IN R.H. OPENING AND SWING HANDLE
SLIGHTLY TO THE RIGHT TO DEFLECT
INTERNAL CLASP. RIGHT HAND SIDE OF
COVER WILL NOW SWING OUT.
India
Building 13, No.99 Tianzhou Road
ShangHai, P.R. China 200223
Fax [phone]
Tel [phone]
Unit 101, XinAn Plaza
Red Lion Controls
China