DRT2-OD32BV-1 Omron, DRT2-OD32BV-1 Datasheet - Page 488
DRT2-OD32BV-1
Manufacturer Part Number
DRT2-OD32BV-1
Description
32 Out Vert MIL Connector PNP
Manufacturer
Omron
Datasheet
1.DRT2-OD16.pdf
(600 pages)
Specifications of DRT2-OD32BV-1
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
- Current page: 488 of 600
- Download datasheet (13Mb)
Inspection Equipment
Equipment Required for
Regular Inspection
Other Equipment that May
Be Required
Inspection Procedure
9-3-3
Precautions
Settings after
Replacing Units
Maintenance
Environmental condi-
tions
Installation condi-
tions
Inspection item
Replacing Units
Are ambient and cabinet tem-
peratures correct?
Are ambient and cabinet
humidity correct?
Has dust or dirt accumulated? No dust or dirt
Are the Units installed
securely?
Are the connectors of the
communications cables fully
inserted?
Are the external wiring screws
tight?
Are the connecting cables
undamaged?
Details
Prepare the following equipment before inspecting the system.
A flat-blade and a Phillips screwdriver, a screwdriver for connecting communi-
cations connectors, a tester (or a digital voltmeter), industrial alcohol, and a
clean cloth are required for routine inspection.
A synchroscope, oscilloscope, thermometer, or hygrometer may be required.
Check the items in the following table and correct any condition that is below
standard.
The Network consists of the DeviceNet Master Unit and Slave Units. The
entire network is affected when a Unit is faulty, so a faulty Unit must be
repaired or replaced quickly. We recommend having spare Units available to
restore Net-work operation as quickly as possible.
Observe the following precautions when replacing a faulty Unit.
After replacement make sure that there are no errors with the new Unit.
When a Unit is being returned for repair, attach a sheet of paper detailing the
problem and return the Unit to your OMRON dealer.
If there is a faulty contact, try wiping the contact with a clean, lint-free cloth
dampened with alcohol.
After replacing a Unit, set the new Unit's switches to the same settings that
were on the old Unit.
Refer to the specifications for
each Slave.
Refer to the specifications for
each Slave.
No looseness
No looseness
No looseness
No external damage
Standard
Visual inspection
Thermometer
Hygrometer
Phillips screwdriver
Phillips screwdriver
Phillips screwdriver
Visual inspection
Equipment
Section 9-3
467
Related parts for DRT2-OD32BV-1
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
DRT2 Mix IO E-Con 8in/out PNP
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
DRT2 16 OutMIL Conn Cable With
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
DRT2 16 In MIL Connector NPN
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
DRT2 16 In MIL Connector PNP
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
DRT2 16 In MIL Conn Cable With
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
DRT2 16 In MIL Conn Cable With
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
DRT2 Mix IO E-Con8 In/out, NPN
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
DRT2 8 Out TermOutal NPN
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
G6S-2GLow Signal Relay
Manufacturer:
Omron Corporation
Datasheet:
Part Number:
Description:
Compact, Low-cost, SSR Switching 5 to 20 A
Manufacturer:
Omron Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet: