DZ-10GW2-1A Omron, DZ-10GW2-1A Datasheet
![BASIC SWITCH](/photos/17/65/176574/dz-10g-1b_t_sml.jpg)
DZ-10GW2-1A
Specifications of DZ-10GW2-1A
DZ10GW21ANC
Related parts for DZ-10GW2-1A
DZ-10GW2-1A Summary of contents
Page 1
... Ratings 10 (250 VAC) 2. Contact Gap G: 0.5 mm Solder terminal (-1A) Model DZ-10G-1A DZ-10GW-1A DZ-10GV-1A DZ-10GW22-1A DZ-10GV22-1A DZ-10GW2-1A DZ-10GV2-1A 3. Actuator None: Pin plunger Low OT Levers: V: Hinge lever V22: Short hinge roller lever V2: Hinge roller lever High OT Levers: W: Hinge lever W22: Short hinge roller lever ...
Page 2
... Operating frequency: 20 operations/min ■ Safety Standard Ratings UL/CSA Silver alloy 0.5 mm Rated voltage 30 A max. 125 VAC 15 A max. 250 VAC 480 VAC 125 VDC 250 VDC DZ Inductive load (A) Motor load 1.5 4 0.05 0.05 0.03 0.03 DZ-10G 10 A and 1 and 1 0.5 A 0.25 A ...
Page 3
... Switch. Tighten the screws to a torque of 1.18 to 1.47 N·m. Two, 4.2 dia. mounting holes or M4 screw holes ± 0.1 25.4 Accessories (Terminal Covers, and Separators): Refer to ‘Z/A/X/DZ Common Accessories’ datasheet ■ Electrical Durability (DZ-10G-1B) 1,000 0.7 0.8 Solder Terminals (-1A) 14 ...
Page 4
... Hinge Lever DZ-10GW-1B 19.7 17.7 DZ-10GV- 14.5 +0.075 4.2 -0.025 Short Hinge Roller Lever DZ-10GW22-1B 19.7 17.7 DZ-10GV22- 14.5 92 Special-purpose Basic Switch 3 dia. 2.5SR * ± 0.25 23.3 +0.1 4.36 dia. -0.05 +0.075 ± 0.2 17.45 11.9 4.2 dia. hole -0 ...
Page 5
... Stainless-steel lever 49.2 Special-purpose Basic Switch 9.5 dia. × 4 (plastic roller) OF max. 213 gf RF min min. 1 max. 3 max. 47 31.8±0.8 mm 17.45 ± 0.2 * Stainless-steel lever 9.5 dia. × 4 (plastic roller) OF max. 270 gf RF min max min. 0. max. 1 29.4±0.8 mm 17.45 ± 0 ...
Page 6
... If there is silicon oil, silicon filling, silicon wiring, or other silicon products in the vicinity of the switch, use a contact protection circuit to limit arcing and remove the source of the silicon gas. DZ Correct Separate the installation lo- cation from heat sources ...
Page 7
... DZ Special-purpose Basic Switch MEMO ...
Page 8
... To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527. OMRON ELECTRONIC COMPONENTS LLC 55 E. Commerce Drive, Suite B Schaumburg, IL 60173 847-882-2288 11/10 Cat. No. X303-E-1 Special-purpose Basic Switch OMRON ON-LINE Global - http://www.omron.com USA - http://www.components.omron.com Specifications subject to change without notice DZ Printed in USA ...