Z-15GD55-MD Omron, Z-15GD55-MD Datasheet - Page 19

• Manufacturer Part Number: Z-15GD55-MD
• Description: BASIC SWITCH
• Manufacturer: Omron
• Series: Zr

Specifications of Z-15GD55-MD

• Circuit: SPDT
• Switch Function: On-Mom
• Contact Rating @ Voltage: 15A @ 125VAC
• Actuator Type: Round (Pin Plunger)
• Mounting Type: Chassis Mount
• Termination Style: Cable Leads
• Operating Force: 540gf
• Pole Throw Configuration: SPDT
• Switch Function Configuration: N.O./N.C.
• Actuator Style: Short Spring Plunger
• Actuator Material: Stainless Steel
• Current Rating (max): 15A
• Ac Voltage Rating (max): 500VVAC
• Dc Voltage Rating (max): 250VVDC
• Mechanical Life: 10000000
• Terminal Type: Wire Lead
• Product Depth (mm): 17.45mm
• Product Length (mm): 49.2mm
• Operating Temp Range: -15C to 80C
• Contact Form: SPDT
• Contact Rating: 15 Amps at 250 Volts
• Actuator: Plunger
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: Z15GD55MD; Z15GD55MDNC

Note: 1. All drawings show the switches with screw terminals. For versions with solder terminals, remove the “-B” from the end of the part number.
Flexible Rod (Coil Spring)
Z-15GNJ55-B
Flexible Rod (Steel Wire)
Z-15HNJS55-B
2. Unless otherwise specified, all units are in millimeters and a tolerance of ± 0.4 mm applies to all dimensions.
(111.3)
(130.1)
100
(13.6)
(13.8)
43.4
16.3
16.3
38
± 0.4
4.2
4.2
(22)
+0.075
+0.075
-0.025
-0.025
PT
PT
4.36
4.36
25.4
25.4
49.2
49.2
23.3
23.3
+0.1
+0.1
-0.05
-0.05
30 Operating range *2
30 Operating range *2
± 0.1
± 0.1
Four, M3 set screws
with hexagonal holes
± 0.25
± 0.25
Rubber cap
Rubber cap
dia.
dia.
11.9
11.9
4.2
4.2
+0.075
+0.075
-0.025
-0.025
dia. hole
dia. hole
1-dia. stainless
steel wire *3
Nylon rod
12 dia.
12 dia.
9.2
9.2
6.1 dia.
3.2 dia.
17.45
17.45
*1
*1
General-purpose Basic Switch
± 0.2
± 0.2
*1. Operation is possible in any direction other than the
*2. Use only the area within the top 30 mm of the rod as
*1. Operation is possible in any direction other than the axial
*2. Use only the area within the top 30 mm of the rod as the
*3. The steel wire can be replaced if damaged.
axial direction (indicated by the arrow
the operating part. (Do not use the area that falls within
80 mm from the mounting hole as the operating part.
Using this area may cause damage to the nylon rod.
direction (indicated by the arrow
operating part. (Do not use the area that falls within 100
mm from the mounting hole as the operating part.
Using this area may cause damage to the steel wire.)
(Model: Lever for HNJS55)
OF max.
PT max.
OF max.
PT max.
TT max.
).
).
Z
(25 mm)
(20 mm)
40 mm
15 gf
50 gf
165