D10BFPQ BANNER ENGINEERING, D10BFPQ Datasheet - Page 5

• Manufacturer Part Number: D10BFPQ
• Description: D10BFPQ QD 6 PIN PICO RED
• Manufacturer: BANNER ENGINEERING
• Type: Fiber Opticr

Specifications of D10BFPQ

• Brand/series: D10 Expert™
• Current, Switching: 150 mA
• Function: Fiber Optic
• Ip Rating: IP50
• Mounting Type: Bracket
• Output: NPN/PNP
• Primary Type: Photoelectric
• Sensing Mode: Selectable
• Technology: Photoelectric
• Termination: 6-Wire Connector
• Voltage, Supply: 30 VDC
• Accessories Available: Cordsets and Plastic Fiber Optic Cable

Figure 4. Window SET (Light Operate
(no signal)
(no signal)
(no signal)
(no signal)
Darkest
Darkest
Darkest
Darkest
the presented condition
threshold 12.5% above
Output OFF
Banner Engineering Corp. • Minneapolis, MN U.S.A
Sensor positions
T
T
T T T
Output OFF
Output OFF
Output OFF
0.8 seconds
> 2 seconds
T
T
T T T
shown)
•
•
•
0.04 seconds ≤ “Click” ≤ 0.8 seconds
0.8 seconds
> 2 seconds
Press and hold Static push
Present sensing condition.
Double-click Static push
button > 2 seconds.
button.
Presented
Condition
Sensing window size
Threshold position
Threshold position
Manual Adjust
Manual Adjust
Manual Adjust
Manual Adjust
adjusted by
adjusted by
adjusted by
adjusted by
Output ON
Presented
Condition
Push Button
Position
or
or
Condition
Presented
T
Sensor positions
threshold 12.5% below
the presented condition
T
T
Output ON
Output ON
Output ON
T
T
T
Sensor positions
window thresholds
12.5% from the
presented condition
Output OFF
T
T
T
T
T
T
T
T
T
Most Light
Most Light
Most Light
Most Light
(saturated
(saturated
(saturated
(saturated
signal)
signal)
signal)
signal)
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
0.04 seconds ≤ T ≤ 0.8 seconds
•
•
•
T
Single-pulse remote line.
Present sensing
Double-pulse remote
condition.
T
line.
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
Window SET is most useful when a product may not always appear in the same place,
or when other signals may appear. Window SET designates a sensing window, with
the Output ON condition inside the window, and the Output OFF conditions outside
the window (see Figure 4). The sensor accepts a single sensing condition, and adds
switching thresholds above and below that condition to create a sensing window. Output
ON and OFF conditions can be reversed by changing Light/Dark Operate status in
SETUP mode.
Window SET and Manual Adjust
Using Manual Adjust with Window SET expands or contracts the size of the window. The
lighted LEDs on the light bar separate to a greater or lesser extent to exhibit the relative
sensing window size.
Remote Line
T
T
T
T
T
T
T
T
T
T
T
• Sets a single ON condition that extends 12.5% above and below the taught condition
•
(Manual Adjust)
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
1x
2x
3x
4x
5x
6x
7x
1x
2x
3x
4x
5x
6x
7x
Power LED: OFF
Output LED: ON (Push Button)
Output LED: OFF (Remote)
Static LEDs:
Window Accepted
Power LED: ON
Bargraph:
Sensor returns to RUN mode with new settings.
Window Unacceptable
Power LED: OFF
Bargraph:
Sensor returns to “SET Sensing Condition.”
Single-Point Window SET
2 indicators flash together
#1, 3, 5, 7 flash to show
to show Window accepted
failure
LO & DO alternately
flashing
Result
P/N 117830 rev. E
or
5