CRA06S083150RFTA Vishay, CRA06S083150RFTA Datasheet - Page 3

• Manufacturer Part Number: CRA06S083150RFTA
• Description: RESISTOR, RES ARRAY, 4, 150OHM, 5%, SMD
• Manufacturer: Vishay
• Type: Arrayr
• Series: CRA06Sr

Specifications of CRA06S083150RFTA

• Resistance: 150Ohm
• Temperature Coefficient: ±100
• Technology: Thick Film
• Power Rating Per Resistor: 1/16W
• Number Of Resistors: 4
• Tolerance (+ Or -): 1%
• Circuit Designator: ISOL
• Mounting Style: Surface Mount
• Military Standard: Not Required
• Operating Temp Range: -55C to 155C
• No. Of Terminals: 8
• Case Style: Molded
• Failure Rate: Not Required
• Termination Style: Convex
• Terminal Pitch: 0.8
• Product Length (mm): 3.2mm
• Product Depth (mm): 1.5mm
• Product Height (mm): 0.5mm
• Resistance Tolerance: ± 5%
• Power Rating: 63mW
• Voltage Rating: 50V
• No. Of Elements: 4
• Resistor Case Style: SOIC
• Lead Free Status / RoHS Status: Compliant

CRA06E, CRA06S
Vishay
Notes
(1)
(2)
www.vishay.com
254
TEST PROCEDURES AND REQUIREMENTS
TEST
(clause)
Resistance (4.5)
Temperature coefficient (4.8.4.2)
Overload (4.13)
Solderability (4.17.5)
Resistance to soldering heat (4.18.2)
Rapid change of temperature (4.19)
Damp heat, steady state (4.24)
Climatic sequence (4.23)
Endurance at 70 °C (4.25.1)
Extended endurance (4.25.1.8)
Endurance at upper category
temperature (4.25.3)
APPLICABLE SPECIFICATIONS
• EN 60115-1
• EN 140400
• EN 140401-802
• IEC 60068-2-X
• EIA 481
Figures are given for a single element
Solderability is specified for 2 years after production or requalification. Permitted storage time is 20 years
(2)
Generic Specification
Sectional Specification
Detail Specification
Variety of environmental test procedures
Packaging of SMD components
For technical questions, contact: [e-mail]
CONDITIONS OF TEST
Stability for product types:
16 h at UCT = 125 °C; 1 cycle at 55 °C;
U = U
U = U
30 min at UCT = 125 °C; 5 cycles
solder bath method; 235 °C; 2 s
Aging 4 h at 155 °C, dryheat
Duration extended to 8000 h
Thick Film Resistor Array
1 h/1 kPa at 15 °C to 35 °C;
30 min at LCT = - 55 °C;
(260 ± 5) °C; (10 ± 1) s
max.
max.
UCT = 125 °C; 1000 h
U = 2.5 × (P
1.5 h ON; 0.5 h OFF;
(40 ± 2) °C; 56 days;
2 h at LCT = - 55 °C;
Solder bath method;
visual examination
20/- 55/20 °C and
≤ 2 x U
5 cycles at 55 °C
; whichever is less severe
; whichever is less severe
U = (P
U = (P
(93 ± 3) % RH
70 °C; 1000 h
20/125/20 °C
max.
70
70
-
EN 60115-1
x R)
x R)
70
CRA06E/CRA06S
; 0.5 s
x R)
1/2
1/2
1/2
CLASS 1 OR BETTER
± (0.25 % R + 0.05 Ω)
± (0.25 % R + 0.05 Ω)
± (0.25 % R + 0.05 Ω)
± (1 % R + 0.05 Ω)
± (1 % R + 0.05 Ω)
± (1 % R + 0.05 Ω)
± (1 % R + 0.05 Ω)
± (2 % R + 0.1 Ω)
10 Ω to 1 MΩ
± 100 ppm/K
STABILITY
PERMISSIBLE CHANGE (ΔR/R)
± 1 %
Good tinning (≥ 95 % covered)
REQUIREMENTS
no visible damage
Document Number: 31002
CLASS 2 OR BETTER
± (0.5 % R + 0.05 Ω)
± (0.5 % R + 0.05 Ω)
± (0.5 % R + 0.05 Ω)
± (2 % R + 0.1 Ω)
± (2 % R + 0.1 Ω)
± (2 % R + 0.1 Ω)
± (4 % R + 0.1 Ω)
± (2 % R + 0.1 Ω)
10 Ω to 1 MΩ
± 2 %; ± 5 %
± 200 ppm/K
Revision: 13-Oct-08
STABILITY
(1)