MH14-6R/L 3M Interconnect Solutions, MH14-6R/L Datasheet - Page 2

• Manufacturer Part Number: MH14-6R/L
• Manufacturer: 3M Interconnect Solutions

Specifications of MH14-6R/L

• Lead Free Status / RoHS Status: Supplier Unconfirmed

3M is a trademark of 3M.
Electrical Products Division
6801 River Place Blvd.
Austin, TX 78726-9000
http://www.3M.com/elpd
IMPORTANT NOTICE
Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability
associated with such use.
Warranty; Limited Remedy; Limited Liability. This product will be free from defects in material and manufacture as of the date of purchase.
3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be,
at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except where prohibited by law, 3M will
not be liable for any loss or damage arising from this 3M product, whether direct, indirect, special, incidental or consequential
regardless of the legal theory asserted.
Specifications
Wire Size:
Barrel Seam:
Max. Voltage Rating:
Max. Operating Temp.:
Max. Current:
Insulator Material:
Terminal Material:
Terminal Plating:
Installation Information
UL Listed and CSA Certified for use on stranded copper
(AWG) wire only.
Strip away the end 3/8 inch of wire insulation.
Make the crimp in the proper station of a recommended
3M crimp tool: TH-440, TH-450 (scissor style) hand
tools.
Shrink tubing using a heat gun. Heat until tubing is
completely shrunk and adhesive protrudes slightly from
the tubing.
is a trademark of Underwriters Laboratories.
is a trademark of Canadian Standards Association.
WARNING
Turn power off before installing or removing terminal. All electrical
work should be done according to appropriate electrical codes.
See Table Above
Brazed
600 V Building Wire
1000 V Signs, Fixtures
and Luminaires
221˚F (105˚C)
Same as Wire
Adhesive-lined
Polyolefin, TMW
ETP Copper
Tin
Barrel Crimp (Electrical)
Engineering Specification
Crimp-type terminals shall, electrically and
mechnically, connect to a pre-stripped end of a
stranded copper wire and have a flat tongue portion
with a central opening for mounting around a screw or
stud.
The terminal line shall offer tongue variations in hole
(stud) size (6, 8 10, etc.) and configuration (ring, fork,
block fork, flanged block fork, locking fork, etc.): and
barrel variations in wire (AWG) size (22-18, 16-14,
12-10, etc.) and construction (non-insulated brazed
seam, vinyl insulated butted seam, nylon insulated
with insulation grip, etc.). The terminal line shall have
regulatory agency coverage (UL Listing, CSA
Certification). The terminal tongue shall be marked
with the wire range and manufacturer’s symbol ( ).
The heat shrink-insulated, brazed seam ring tongue
terminal shall be tin-plated, annealed copper, with the
tongue having a specified stud slot (size 6 thru 3/8 in.)
and a brazed seam barrel covered by an adhesive-lined
heat shrink sleeve, color coded and sized for a
specified (AWG) wire range (22-18, 16-14, 12-10.).
Heat shrink terminals shall be UL Listed and CSA
Certified for 600 Volts maximum building wire: 1000
Volts maximum in signs, fixtures and luminaries and
have a maximum operating temperature of 221°F
(105°C).
© 3M 2002 78-8126-0835-0-A
Litho in USA.